Exhaust Housing Seal 0320936
- This is an OEM part manufactured by Evinrude & Johnson, OMC
- Flat rate shipping starting at $4.95
- 30 day return policy
Product Description
Product Questions
There are no questions for this product. Ask a new question and receive an answer, directly from our support staff.
98 Product Reviews
'05 Etec 250
- Repair Difficulty
- Hard
- Repair Time
- More than 4 hours
Problem fixed: Hole in piston
Needed several parts besides the rebuilt powerhead I'm still about 6 hours from finishing
1998 Evinrude 115 Ficht Intruder
- Repair Difficulty
- Medium
- Repair Time
- 2 to 4 hours
Problem fixed: Replaced water pump as a preventative maintenance issue.
Followed the manual for removal and replacement. No real issues except getting shift rod back into linkage. There is very little visibility of the head of the shift rod. Recommend having a helper to rotate and lightly pull the shift arm (starboard side of motor) while you align the rod from the port side. Plus the shift rod needs to be extended all the way up to align. Great, except when it gets inserted into the upper housing, it will probably get pushed down to neutral or reverse. I took a long Phillips screwdriver, hooked it through the hole in the rod, and was able to get it pulled back up. I also used a small ratchet strap to pre-flex the impeller arms into the proper curved shape. Then just aligned it with the cup (greased) and slid it out of the strap and into the cup.
Evinrude 120
Johnson 225
2005 Johnson
Johnson 90hp
- Repair Difficulty
- Easy
- Repair Time
- 30 to 60 mins
Problem fixed: Crappy water pump
Replaced parts
Evinrude 200HO
- Repair Difficulty
- Easy
- Repair Time
- 1 to 2 hours
Problem fixed: Waterpump Rebuild
Water pump rebuild kit had all of the components needed, except gasket seals/greases. Which was to be expected. Encountered two unexpected issues, which it would be good to plan for. 1) Brass ring on the old impellor had corroded itself to the drive shaft. Needed to get a cutting wheel for a dremel to remove. Once a deep notch was cut, I was able to split the ring and remove. 2) Shift lever was not quite aligned with the linkage when the lower unit was replaced. Its height was correct but was set slightly too far aft to allow the screw to grab. Needed a long screwdriver (or knitting needle) to nudge back into place, while using a claw tool to reinsert screw holding the shift rod and linkage together.
E115FSLSRE
evinrude 200 hp
- Repair Difficulty
- Medium
- Repair Time
- 1 to 2 hours
Problem fixed: new water pump
removed lower unit replaced pump and exhaust gaskets installed lower unit
Evinrude 250
2004 evinrude 150 e150fhlsrs
- Repair Difficulty
- Easy
- Repair Time
- 1 to 2 hours
Problem fixed: lower unit broke off lost in lake
replaced the exhaust housing .upper exhaust and lower .replaced lower unit.
140 Evinrude
Evinrude 150 spitfire
Evinrude 150
06 Evinrude 150
Johnson 150
- Repair Difficulty
- Easy
- Repair Time
- Less than 30 mins
Evanrude 90
Johnson 150 1993
- Repair Difficulty
- Easy
- Repair Time
- 30 to 60 mins
Problem fixed: Low water pressure
Water pump replacement,
2005 Evinrude ETEC 90
- Repair Difficulty
- Hard
- Repair Time
- 2 to 4 hours
Problem fixed: Water pump seals and internal anoid
I needed a new water pump and anoid on lower shaft carrier unit and seals on carrier as well as seals under water pump i ordered parts as usual delivery on time. As i was checking my manual i realized i needed an exhaust seal that i failed to order so called Crowley they had part i opted for three day shipping and got part on time to start repair . these are good people and have had parts when i needed them i will order from them again thank you Crowley Marine Steve B.
1989 evinrude 225
- Repair Difficulty
- Medium
- Repair Time
- 1 to 2 hours
Evinrude
- Repair Difficulty
- Medium
- Repair Time
- 1 to 2 hours
Problem fixed: New water pump, upper exhaust sleeve.
Fist time doing these types of repairs other than on automobiles and smaller engines. Went easy just U tubed it and made it go easy.
Evenrude 150
94 Evinrude
1985 Johnson 140hp
ETEC 150
johnson 140 hp.
- Repair Difficulty
- Hard
- Repair Time
- More than 4 hours
Problem fixed: resealed lower unit
Removed lower unit and disassembled, realized that I needed a Factory Service Manual to reference for pinion gear and shift rod adjustment. I also ordered the OEM gasket sealer. Repair was completed with no leaks.
johnson 90hp
- Repair Difficulty
- Medium
- Repair Time
- Less than 30 mins
Problem fixed: cooling system not working properly.
Disengage lower unit to access the impeller and change the two thermostats on the power head. Relatively, easy.
Evinrude 140
Evinrude 200
- Repair Difficulty
- Easy
- Repair Time
- Less than 30 mins
Problem fixed: Engine sat for more than ten years.
Had an old Evinrude 200 that had been sitting for a long time. Changed out the impeller and put the motor on a bass boat I picked up. It's a gas guzzling beast.
Customers Also purchased
Supersession Chain
Name | SKU | Superceding SKU |
---|---|---|
Exhaust Housing Seal VIEWING THIS PRODUCT | 0320936 | CURRENT |
Shift Bracket Seal | 0777897 | 0320936 |
Aftermarket Product Interchange
Name | SKU | Price | Brand |
---|---|---|---|
Exhaust Leg Rubber Seal | 18-0540 | - | Sierra Marine |