PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Service Manual G2 74° V6 Service Manual 5010014 Engine And Control Systems [Engine Management Module (Emm)]

Produtos Relacionados:
Service Manual G2 74° V6 Service Manual 5010014 Engine And Control Systems [Engine Management Module (Emm)]
5010014
BRP Marine

Step 1: Engine Management Module (EMM)

The Engine Management Module (EMM) is a water-cooled controller. It controls engine management and engine–related remote control functions.

This section discusses the functions of the EMM and its various internal and external sensors. It also describes using Evinrude Diagnostics software to retrieve and adjust service information saved in the EMM.

Step 2: EMM Functions

The EMM controls the following processes and functions:

  • Alternator output; 55 V and 12 V
  • Start Assist Circuit (SAC) voltage boost
  • Fuel and ignition timing and duration
  • Fuel injector activation
  • Oil pump activation
  • Electric fuel lift pump control
  • Electric high pressure fuel pump control
  • Idle speed control
  • RPM limiter
  • Electrical circuit monitoring
  • Fault code creation and storage
  • Warning system activation
  • ROM verification, self-test
  • Cold starting
  • Output of diagnostic data
  • Tachometer signal
  • RPM profile and engine hours
  • Oil pump activation
  • Anti-knock compensation
  • Electronic throttle control
  • Electronic shift control
  • Dynamic Power Steering

Step 3: EMM Connections

IMPORTANT: EMM connections and wiring must be clean and tight. Improper electrical connections can damage the EMM. DO NOT run the outboard with loose or disconnected wiring.

Make sure EMM connections are clean and tight.
• Engine wire harness to EMM connectors; J1-A, J1-B, J2, J3, J4.
• Stator to EMM connections; one 6-pin AMP and J2 connector.

  1. J1-A connector
  2. J1-B connector
  3. J2 connector
  4. J3 connector
  5. J4 connector

Step 4: EMM Inputs and Outputs Diagram

  1. EMM
  2. 12 VDC Battery
  3. Fuel Vapor Separator
  4. Electronic Throttle Body
  5. Shift Actuator
  6. Knock Sensor (2)
  7. Engine Temperature Sensor (2)
  8. Exhaust Temperature Sender
  9. Engine Oil Level Sender
  10. Trim Sender
  11. (reserved for future use)
  12. DPS Pressure Sensors
  13. Digital Remote Control
  14. Intake Air Temperature Sensor
  15. Crankshaft Position Sensor
  16. Water in Fuel Sensor
  17. Stator
  18. Low Oil Switch
  19. Trim Switch
  20. (reserved for future use)
  21. Fuel Injector (6)
  22. Ignition Coil (6)
  23. Water Valve
  24. Digital Displays & Gauges
  25. Dynamic Power Steering Module
  26. Oil Pumps
  27. Starter Solenoid & Motor
  28. Trim & Tilt Relay
  29. Vapor Vent Solenoid
Share on social:

Produtos Relacionados