PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Homenageamos todos os que serviram: veteranos, militares no ativo e socorristas poupam 5 % nas peças OEM durante todo o ano. Os nossos armazéns e o apoio ao cliente estão abertos no Dia dos Veteranos, 11 de novembro.

Contate-Nos
Estoque excedente
Até 50% de desconto
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia
Onde está o número do meu modelo?

Service Manual 5009009_115–200 HP 60°V - V4 AA-AE - V6 AA Remote Control System [Icon Component Servicing]

Produtos Relacionados:
added updated
Service Manual 5009009_115–200 HP 60°V - V4 AA-AE - V6 AA Remote Control System [Icon Component Servicing]
5009009
BRP Marine

Sections:

  1. ICON COMPONENT SERVICING
  2. Electronic Servo Module (ESM)
  3. Shift Actuator
  4. Throttle Actuator

ICON COMPONENT SERVICING

To prevent accidental starting while servicing, disconnect the battery cables at the battery.

Electronic Servo Module (ESM)

Disconnect the battery cables at the battery. Remove the flywheel cover and air silencer.

Removal
Disconnect the:

  • ICON buss cable from ESM

  • ESM CANbus harness from EMM

  • ESM throttle actuator harness

  • ESM shift actuator harness

  • ESM power supply harness from solenoid and ground stud

Remove the ESM from studs.

  1. Studs

Installation
Install grommets on ESM. Apply soapy water to grommets and push assembly on to studs.

  1. Grommets

  1. Studs

Route the CANbus harness from the ESM around the flywheel cover to the EMM as shown and secure with tie straps.

  1. CANbus harness

  1. CANbus harness

Continue harness routing to the EMM connector. Make sure harness is not strained.

  1. EMM CANbus connector

Route ESM harnesses as shown and secure with tie straps. ESM to boat network cable should go behind and to the port side of the other cables.

  1. Network cable

  1. Network cable

Route ESM power supply harness negative (–) terminal to engine main ground screw. Tighten screw to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

  1. ESM Power supply negative (–)
  2. Ground screw

Route ESM power supply harness positive (+) terminal to solenoid positive terminal. Install copper crush washer over ESM positive ring terminal.

  1. ESM Power supply positive (+)
  2. Copper washer

Route battery cable as shown. Install negative cable on double-ended stud. Install star washer, positive battery cable, and nut on solenoid terminal. Tighten nuts to a torque of 60 to 84 in. lbs (7 to 9.5 N·m). Coat connections with Black Neoprene Dip.

  1. Battery cable negative (–)
  2. Battery cable positive (+)
  3. Tie strap

Route battery cable and ESM to boat network cable out through the rigging grommet.

  1. Network cable

Install the flywheel cover. Connect the battery cables at the battery.

IMPORTANT: Calibrate shift and throttle actuators. Refer to Calibrate Actuator Stroke on p. 208.

Shift Actuator

Removal

Disconnect the battery cables at the battery. Remove the starboard lower engine cover.

Observe and note all wire routings before disassembling.

Remove clips and washers from the shift link.

Remove the shift link.

  1. Shift link

Remove the shift actuator connector from the clip on the mounting plate. Disconnect the shift actuator harness.

  1. Shift actuator connector

Remove the clamp retaining screw.

Remove the four shift actuator retaining screws.

  1. Clamp retaining screw
  2. Shift actuator retaining screws

Installation

Remove old adhesive from clamp retaining screw and shift actuator retaining screws.

Apply Nut Lock to the threads of the screws.

Install shift actuator on mounting plate with three long screws and one short screw. Tighten screws to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

Place clamp over actuator motor. Install and tighten screw to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

  1. Shift actuator retaining screws
  2. Clamp retaining screw

Connect the shift actuator harness. Attach to clip on mounting plate.

  1. Shift actuator connector

Route all harnesses as shown and secure with tie straps.

Install the starboard lower engine cover. Connect the battery cables at the battery.

IMPORTANT: Do not install shift link until the calibration procedure has been completed. Refer to Calibrate Actuator Stroke on p. 208.

Throttle Actuator

Removal
Disconnect the battery cables at the battery. Remove the flywheel cover and air silencer.

Observe and note all wire routings before disassembling.

Remove the throttle actuator connector from the clip on the mounting plate. Disconnect the throttle actuator harness.

  1. Throttle actuator connector

Remove the clamp retaining screw.

  1. Clamp retaining screw

Use Ball Socket Remover tool, P/N 342226, to remove throttle link from actuator arm.

Remove the four throttle actuator retaining screws.

  1. Throttle actuator retaining screws

Installation

Remove old adhesive from clamp retaining screw and shift actuator retaining screws.

Apply Nut Lock on the threads of the screws.

Install throttle actuator on mounting plate with three long screws and one short screw. Tighten screws to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

Place clamp over actuator motor. Install and tighten screw to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

  1. Throttle actuator retaining screws
  2. Clamp retaining screw

Use Ball Socket Installer tool, P/N 342225, to snap throttle link onto actuator arm.

Share on social:

Produtos Relacionados