PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Service Manual 25-30 HP E-TEC Gearcase [Bearing And Seal Removal]

Produtos Relacionados:
Service Manual 25-30 HP E-TEC Gearcase [Bearing And Seal Removal]
5007802
BRP Marine

Step 1: BEARING AND SEAL REMOVAL

IMPORTANT: Inspect bearings for damage while in place. If bearing is damaged, remove and discard. If the bearing is removed for any reason, it must be replaced

Step 2: Driveshaft Seals

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove the two driveshaft seals. Discard the seals.

Step 3: Driveshaft Bearing

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131 to remove the driveshaft bearing and sleeve from the gearcase. Discard the bearing.

Step 4: Pinion Bearings

Assemble the following components from Universal Pinion Bearing Remover and Installer, P/N 5005927.

  1. Rod, P/N 326582
  2. Pilot Plate, P/N 326583
  3. Remover and Installer, P/N 326577
  4. 1/4-20 x 1/2 in. hex head screw
  5. 1/4-20 x 11/4 in. hex head screw
  6. 1 in. O.D. flat washer

Place the tool in gearcase. using a mallet, drive the pinion bearings into the gearcase propeller shaft cavity. Discard the bearings.

Step 5: Forward Bearing

Use Slide Hammer, P/N 432128, and Bearing Puller, P/N 432130, to remove the forward bearing cup from the gearcase.

Secure the puller jaws into grooves behind the cup. Use Wrench, P/N 334359, to hold the puller while tightening the jaws.

  1. Bearing puller
  2. Wrench

Step 6: Shift Rod Bushing and O-ring

Position Shift Rod Bushing Remover, P/N 327693, under the shift rod bushing.

Thread the adapter of the Slide Hammer, P/N 391008, in the slide hammer. Place the adapter through the shift rod bushing and thread into the remover tool.

Remove the handle from the remover tool. Then remove the bushing from the gearcase.

Once the bushing has been removed from the gearcase, examine the bushing for damage. If damaged, replace the bushing on reassembly. Remove and discard the O-ring(s) and washer from the bushing.

  1. Adapter
  2. Shift rod bushing
  3. Remover tool, P/N 327693

Step 7: Prop Shaft Bearing Housing Seals and O-ring

Remove and discard the propeller shaft bearing housing O-ring.

  1. O-ring

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove seals. Discard seals.

  1. Small puller jaws

Useg Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove both propellers shaft bearings from the bearing housing. Discard both bearings.

  1. Small puller
Share on social:

Produtos Relacionados