PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Power Unit [Recoil Starter] [2008]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 2001 - 2005 4hp All
Yamaha Outboard 1999 - 2005 4hp All

Power Unit [Recoil Starter] [2008]
LIT-18616-01-79
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
RECOIL STARTER REMOVAL Follow the left "Step" for removal.
1 Start-in-gear protection cable 1
2 Choke wire 1
3 Bolt with washer (recoil starter) 2
4 Bolt with washer (recoil starter) 1
5 Recoil starter ass'y 1
Reverse the removal steps for installation.

Step Procedure/Part name Q'ty Service points
RECOIL STARTER DISASSEMBLY Follow the left "Step" for disassembly.
(1) Screw (drive plate) 1
(2) Drive plate 1
(3) Drive pawl 2
(4) Pawl springs 2
(5) Sheave drum 1
(6) Spiral spring 1
(7) Clip (drive plate) 1
(8) Plate (starter handle) 1
(9) Starter rope 1 NOTE:
Apply grease and make sure to reef knot both ends, after installation.

Step Procedure/Part name Q'ty Service points
(10) Collar 1
(11) Starter handle 1
(12) Start-in-protection lever 1
(13) Rubber seal 1
(14) Starter case 1
(15) Plate 1
Reverse the disassembly steps for assembly.

SERVICE POINTS

Sheave drum removal

WARNING:

Wear proper safety goggle and gloves to protect your eyes and hands Because: the spiral springs may jump out causing injury.

  1. Rotate:
  • Sheave drum
    Turn the sheave drum clockwise until the spring is free.

NOTE:

  • Turn the sheave drum so that the cutaway on the outer surface of the sheave drum faces toward the starter handle.
  • Pass the starter rope through the cut.

  1. Remove:
  • Bolt
  • Drive plate (1)
  • Drive pawl (2)
  • Sheave drum (3)

WARNING:
Be sure to check that the spiral spring is completely free to prevent it shooting out at you. Then pull the sheave drum carefully upward.

Spiral spring removal

  1. Remove:
  • Spiral spring (1)

WARNING:
Be careful so that the spiral spring does not pop-out when removing it. Remove it by allowing it out one turn of the winding each time.

Start-in-gear protection lever inspection

  1. Inspect:
  • Start-in-gear protection lever
    Crack/wear/damage -> Replace.

Drive pawl and spring inspection

  1. Inspect:
  • Drive pawl
    Crack/wear/damage -> Replace.

  • Drive pawl springs
    Broken/bent/damage —> Replace.

Sheave drum inspection

  1. Inspect:
  • Sheave drum
    Crack/wear/damage -> Replace.

Spiral spring inspection

  1. Inspect:
  • Spiral spring
    Broken/bent/damage —> Replace.

Starter rope inspection

  1. Inspect:
  • Starter rope
    Fray/wear/damage -> Replace.

NOTE:

  • When replacing the rope, cut it the specified length and burn the rope end so that it will not trouble.

  • Apply water resistant grease sufficiently on the new starter rope.

Starter rope length: 1,800 mm (70.9 in)

Starter rope installation

  1. Install:
  • Starter rope

NOTE:

  • Insert the rope through the rope holes and knot the end.

  • Wind the rope 2-1/2 turns around the sheave drum.

  • Place the rope at the cutaway.

Sheave drum installation

  1. Install:
  • Sheave drum

  • Spiral spring

WARNING:
When installing the spiral spring in the sheave drum, take care to ensure that the spiral spring does not pop out and compress it by winding one turn from outside.

NOTE:

Position the outer end of the spiral spring on the retainer post of the sheave drum.

Spiral spring setting

  1. Set:
  • Spiral spring

NOTE:

Wind up the spring 2-1/2 turns counterclockwise with the starter rope.

Recoil starter checking

  1. Check:
  • Starter operation
    Rough operation -> Repair.

NOTE:

  • When checking the recoil starter only, move out the start-in-gear protection lock.

  • Adjust the start-in-gear protection wire, after install the recoil starter ass'y to the power unit. Refer to page 3-5.

Share on social:

Produtos Relacionados