PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Power Unit [Recoil Starter] [2002]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Power Unit [Recoil Starter] [2002]
LIT-18616-01-65
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
RECOIL STARTER REMOVAL Follow the left "Step" for removal.
1 Start-in-gear protection wire 1 - for start-in-gear protection model
2 Bolt (with washer) 3 6 x 20 mm
3 Collar 3
4 Recoil starter assembly 1
Step Procedure/Part name Q'ty Service points
RECOIL STARTER DISASSEMBLY
1 Cotter pin 1 for start-in-gear protection model
2 Plane washer 1
3 Reel stopper 1
4 Stopper arm 1
5 Spring 1
6 Screw 1
7 Cover 1
8 Starter handle 1
9 Starter rope 1
10 Bolt (with washer) 1
11 Drive plate 1
12 Drive pawl spring 1
13 Sheave drum assembly 1 NOTE:
Position the inner end of the spiral spring on the retainer post of the sheave drum.
Wind up the spring 2-1/2 turns counter clockwise with the starter rope.
14 Bushing 1
15 Spiral spring 1
16 Starter case 1
Step Procedure/Part name Q'ty Service points
SHEAVE DRUM DISASSEMBLY
17 Circlip 1
18 Drive pawl 1
19 Spring 1
20 Return spring 1
21 Rope guide 1
22 Starter rope 1 NOTE:
Wind the rope 2 turns around the sheave. drum.
23 Sheave drum 1
Reverse the removal steps for installation.

SERVICE POINTS

Sheave drum removal

1.Turn:

  • Sheave drum (1)
    Turn the sheave drum clockwise until the spiral spring is free.

NOTE:

  • Turn the sheave drum so that the cutaway on the outer surface of the sheave drum faces toward the starter handle.
  • Pass the starter rope through the cut.

  1. Remove:
  • Sheave drum

WARNING:
When removing the sheave drum, be sure to turn the sheave drum upside down to prevent the spiral spring from popping up at you.

Spiral spring removal

  1. Remove:
  • Spiral spring (1)

WARNING:
Be careful so that the spiral spring does not pop out when removing it. Remove it by allowing it out one turn of the winding each time.

Starter stopping plunger inspection

  1. Inspect:
  • Starter stopping plunger
    Crack/Wear/Damage -> Replace

Drive pawl and spring inspection

  1. Inspect:
  • Drive pawl
    Crack/Wear/Damage -> Replace.
  • Drive pawl spring
    Broken/Bent/Damage -> Replace.

Bushing inspection

  1. Inspect:
  • Bushing
    Crack/Damage -> Replace.

Sheave drum inspection

  1. Inspect:
  • Sheave drum
    Crack/Damage -> Replace.

Spiral spring inspection

  1. Inspect:
  • Spiral spring
    Broken/Bent/Damage ->Replace.

Starter rope inspection

  1. Inspect:
  • Starter rope
    Fray/Wear/Damage -»Replace.

NOTE:
When replacing the rope, cut it to the specified length and burn the rope end so that it will not travel.

Starter rope length: 1,800 mm (70.9 in)

Recoil starter checking

  1. Check:
  • Starter operation
    Rough operation —> Repair.
Share on social:

Produtos Relacionados