PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Lower Unit [Water Pump And Shift Rod (T50:Ft50B, Ft50C)] [2004]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 2004 60hp All
Yamaha Outboard 2004 60hp All

Lower Unit [Water Pump And Shift Rod (T50:Ft50B, Ft50C)] [2004]
LIT-18616-FT-60
Yamaha Marine

Water pump and shift rod (T50/FT50B, FT50C)

No. Part name Q’ty Remarks Tightening torques Tightening torques Tightening torques Tightening torques
Stage N•m kgf•m ft•lb
1 Shift rod assembly 1
2 Oil seal 1 Not reusable
3 Oil seal housing 1
4 O-ring 1 Not reusable
5 Circlip 1
6 Shift rod 1
7 O-ring 1 Not reusable
8 Bolt 2 M6 x 16 mm
9 Woodruff key 1
10 Bolt 2 M8 x 55 mm
11 Bolt 2 M8 x 45 mm
12 Water pump housing 1
13 Grommet 1
14 Gasket 1 Not reusable
15 Insert plate cartridge 1
16 Impeller 1
17 Outer plate cartridge 1
18 Gasket 1 Not reusable
19 Dowel pin 2
20 Oil seal housing assembly 1
21 Gasket 1 Not reusable
22 Oil seal housing 1
23 O-ring 1 Not reusable
24 Oil seal 2 Not reusable.

Removing the water pump and shift rod

  1. Remove the water pump assembly and shift rod assembly (1).

Pull up the shift rod assembly a little (a)to disconnect it from the shift slider (2), turn it counterclockwise 90° (b), and then remove it.

Checking the water pump and shift rod

  1. Check the pump housing for deformation. Replace if necessary.

  1. Check the impeller (1)and insert plate cartridge (2) for cracks or wear. Replace if necessary.

S62Y6540

  1. Check the Woodruff key (3)and the groove (a) on the drive shaft for wear. Replace if necessary.

  1. Check the shift rod for cracks or wear. Replace if necessary.

Installing the water pump and shift rod

  1. Install the shift rod assembly (1).

Install the shift rod assembly into the lower case, turn it clockwise 90° (a), and then push it down (b) to connect it to the shift slider (2).

  1. Install the new oil seals into the oil seal housing as shown.

[A] For USA and Canada
[B] For worldwide

Bearing housing oil seal installer (3): YB-06269
Driver handle (4): YB-06071
Needle bearing attachment (5): 90890-06610
Driver rod L3 (6): 90890-06652

  1. Install the new O-ring (7).

  2. Install the new gasket (8), oil seal housing (9), new gasket (10), and outer plate cartridge (11).

  1. Install the Woodruff key into the drive shaft.
  1. Align the groove on the impeller (12) with the Woodruff key (13), and then install it to the drive shaft.

  1. Install the insert plate cartridge (14)and grommet (15) into the pump housing (16).

Align the insert plate cartridge projection (c)with the hole (d) in the pump housing.

  1. Install the new gasket (17), pump housing assembly (16), and dowel pins (18) to the lower case.

  2. Install and tighten the bolts (19).

When installing the pump housing, apply grease to the inside of the housing, and then turn the drive shaft clockwise while pushing down the pump housing.

Share on social:

Produtos Relacionados