PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Lower Unit [Propeller Shaft And Reverse Gear] [2002]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Lower Unit [Propeller Shaft And Reverse Gear] [2002]
LIT-18616-01-65
Yamaha Marine

Step 1: EXPLODED DIAGRAM

Step 2: REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
PROPELLER SHAFT AND REVERSE GEAR REMOVAL Follow the left "Step" for removal.
Gear oil Refer to the "LOWER UNIT" section in chapter 3.
Propeller Refer to the "LOWER UNIT REMOVAL" section.
1 Bolt (with washer 2 6 x 20 mm
2 Propeller shaft housing assembly 1
3 Plate washer 1
4 Propeller shaft 1
5 Cross pin ring 1
6 Cross pin 1 NOTE : By pushing the shift plunger, bring the cross pin hole in the dog clutch with the hole in the shift slider.
7 Dog clutch 1 NOTE : Install the clutch with "F" mark toward the forward gear side.
8 Shift plunger 1
9 Spring 1
PROPELLER SHAFT HOUSING DISASSEMBLY
(1) O-ring 1
(2) O-ring 1
(3) Reverse gear 1
(4) Reverse gear shim *
(5) Ball bearing 1
(6) Oil-seal 2
(7) Needle housing 1
(8) Propeller Shaft housing 1
Reverse the removal steps for installation.

*: As required

Step 3: SERVICE POINTS

Propeller shaft housing removal

  1. Remove:
    • Propeller shaft housing assembly

Bearing housing puller :
  YB-06234..........(1)
  90890-06503 ......(3)
Universal puller :
  YB-06117..........(2)
Stopper guide plate :
  90890-06501 ......(4)
Center bolt :
  90890-06504.......(5)

[A] For USA and CANADA
[B] Except for USA and CANADA

Propeller shaft housing disassembly

  1. Remove:
    • Ball bearing (1)

Slide hammer set :
  YB-06096........(2)
Stopper guide plate :
  90890-06501.....(3)
Bearing puller :
  90890-06535.....(4)
Stopper guide stand :
  90890-06538.....(5)

[A] For USA and CANADA
[b] Except for USA and CANADA

  1. Remove:
    • Needle bearing

Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616

Reverse gear inspection

  1. Inspect:
    • Tooth
    • Dog
      Wear/Damage ➝ Replace

Bearing inspection

  1. Inspect:
    • Bearing
      Pitting/Rumbling ➝ Replace.

Propeller shaft housing inspection

  1. Clean:
    • Propeller shaft housing
      Use a soft brush and solvent
  2. Inspect:
    • Propeller shaft housing
      Crack/Damage ➝ Replace.

Dog clutch inspection

  1. Inspect:
    • Dog clutch
      Wear/Damage ➝ Replace.

Propeller shaft inspection

  1. Inspect:
    • Propeller shaft
      Wear/Damage ➝ Replace

Propeller shaft housing assembly

  1. Install:
    • Needle bearing

Depth (a) : 0 mm (0 in)

Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616

  1. Install:
    • Oil seal

Depth (a) : 3.0 ~ 3.5 mm (0.12 ~ 0.14 in)

Oil seal installer : YB-06168
Driver rod : YB-06071

  1. Install:
    • Ball bearing

Bearing installer : YB-06015
Driver rod : YB-06071

Share on social:

Produtos Relacionados