PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Lower Unit [Backlash (F50:F50A)] [2004]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 2004 60hp All
Yamaha Outboard 2004 60hp All

Lower Unit [Backlash (F50:F50A)] [2004]
LIT-18616-FT-60
Yamaha Marine

Backlash (F50/F50A)

Measuring the forward and reverse gear backlash

  1. Remove the water pump assembly.

  2. Set the gearshift to the nuetral position.

[A] For USA and Canada
[B] For worldwide

Shift rod push arm: YB-06052
Shift rod push arm: 90890-06052

  1. Install the special service tool so that it pushes against the propeller shaft.

[A] For USA and Canada
[B] For worldwide

NOTE:
Tighten the universal puller or center bolt while turning the drive shaft until the drive shaft can no longer be turned.

Bearing housing puller (1): YB-06234
Universal puller (2): YB-06117
Bearing housing puller claw (3): 90890-06564
Stopper guide plate (4): 90890-06501
Center bolt (5): 90890-06504

  1. Install the backlash indicator onto the drive shaft (18 mm [0.71 in] in diameter), then the dial gauge onto the lower unit.

NOTE:
Install the dial gauge so that the plunger (a) contacts the mark (b) on the backlash indicator.

Backlash indicator gauge (6): YB-06265
Backlash indicator (6): 90890-06706
Magnetic plate (7): YB-07003
Magnet base plate (7): 90890-07003
Dial gauge (8): YU-03097
Dial gauge set (8): 90890-01252
Magnet flexible stand (9): YU-34481
Magnet base (9): 90890-06705

  1. Slowly turn the drive shaft clockwise and counterclockwise and measure the backlash when the drive shaft stops in each direction.

Forward gear backlash: 0.18-0.54 mm (0.007-0.021 in)

  1. Add or remove shims if out of specification.
Forward gear blacklash Shim thickness
Less than 0.18mm (0.007)in) To be decreased by (0.36-M)x 0.56
More than 0.54 mm (0.021 in) To be increased by (M-0.36) x 0.56

M: Measurement

Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools from the propeller shaft.

  2. Apply a load to the reverse gear by installing the propeller (10) without the spacer (11), the washer (12) backwards, then the washer (13) as shown.


S62Y6470

NOTE:
Tighten the propeller nut (14) while turning the drive shaft until the drive shaft can no longer be turned.

  1. Slowly turn the drive shaft clockwise and counterclockwise and measuring the backlash when the drive shaft stops in each direction.


S62Y6475

Reverse gear backlash: 0.71-1.07 mm (0.028-0.042 in)

  1. Add or remove shims if out of specification.
Reverse gear backlash Shim thickness
Less than 0.71 mm (0.028 in) To be decreased by (0.89-M)x 0.56
More than 1.07 mm (0.042 in) To be increased by (M-0.89) x 0.56

M: Measurement

Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools, and then install the water pump assembly.
Share on social:

Produtos Relacionados