PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Fuel System [Carburetor] [2002]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Fuel System [Carburetor] [2002]
LIT-18616-01-65
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for removal
Carburetor assembly Refer to the "CARBURETOR REMOVAL"section in chapter 4.
1 Drain screw 1
2 Washer 1
3 Screw (with washer) 4 4x14 mm
4 Float chamber 1
5 Float chamber packing 1
6 Screw 1
7 Arm pin 1
8 Float 1
9 Clip 1
10 Needle valve 1
11 Cap 1
12 Pilot jet 1
13 Main jet 1
14 Main nozzle 1
15 Screw (with washer) 4 4 x 10 mm
16 Plate 1
17 Packing 1
18 Stopping screw 1
19 Spring 1
20 Pilot adjusting screw 1
21 Spring 1
22 Carburetor body 1
FUEL PUMP DISASSEMBLY
(1) Screw (with washer) 4
(2) Pump cover 1
(3) Diaphragm 1
(4) Pump body 1
(5) Screw 2
(6) Seat valve 2
(7) Nut 2
(8) Diaphragm 1
(9) Diaphragm gasket 1
Reverse the removal steps for installation.

SERVICE POINTS

NOTE:
Do not use steelwire for cleaning the jets as this may enlarge the jet diameters and seriously affect performance.

Carburetor inspection

  1. Inspect:
    • Carburetor body
      Crack/Damage ➝ Replace.
      Contamination ➝ Clean
  2. Inspect:
    • Pilot screw
      Bend/Wear ➝ Replace.
  3. Inspect:
    • Main jet
    • Pilot jet
    • Main nozzle
      Contamination ➝ Replace

  1. Inspect:
    • Needle valve
      Grooved wear ➝ Replace.
  2. Inspect:
    • Float
      Crack/Damage ➝ Replace.

Fuel pump inspection

  1. Inspect:
    • Body
      Crack/Leak/Damage ➝ Replace.
  2. Inspect:
    • Seat valve
      Crack/Distortion ➝ Replace.
  3. Inspect:
    • Diaphragm
    Damage ➝ Replace.

Carburetor assembly

  1. Install:
    • Needle valve
    • Float (1)
    • Float pin (2)
    • Screw (3)

NOTE:

  • The float pin should be fit in the slit the carburetor and locked with the screw.
  • After installing, check the smooth movement of the float.
  1. Measure:
    • Float height (a)
      Out of specification ➝ Replace.

Float height (a) : 14.0 ± 1.5 mm (0.55 ± 0.06 in)

NOTE:

  • The float should be resting on the needle valve, but not compressing the needle valve.
  • Take measurement at the end surface of the float opposite to its pivoted side.

  1. Adjust:
    • Pilot screw

Adjustment steps:

  • Screw in the pilot screw until it is lightly seated.
  • Back out by the specified number of turns.

Pilot screw : 1-1/2 ± 1/4 (turns out)

Share on social:

Produtos Relacionados