PREPARE-SE PARA O INVERNO: de 10 % a 50 % de desconto em todas as peças OEM!

A menos que seja proibido pelo fabricante. Não inclui produtos de reposição ou da marca Crowley Marine. Preço conforme marcado.

Os nossos armazéns encerram na quinta-feira, 26, e na sexta-feira, 27 de novembro. Feliz Dia da Thanksgiving dos Estados Unidos!

Contate-Nos
Procure por Mais de 1 Milhão de Peças Originais
Fáceis de usar  diagramas de peças Melhor preço  de garantia Especializado  suporte ao vivo Mais de 50 anos  servindo velejadores Enorme seleção de peças OEM  -  de 1950 a 2026 A maioria das peças em estoque  -  Cumprimento no mesmo dia
Peças em estoque- Realização no mesmo dia

Fuel System [Carburetor] [1998]

Produtos Relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 1998 25hp All
Yamaha Outboard 1998 25hp All

Fuel System [Carburetor] [1998]
LIT-18616-01-77
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY 1 Follow the left "Step" for removal.
Carburetor unit
1 Throttle link rod 1
2 Electrothermal ram retainer 1
3 Electrothermal ram 1
4 O-ring 1
5 Carburetor top cover 1
6 Gasket 1
7 Pilot outletjet 1
8 O-ring 1
9 Throttle stop screw 1
10 Spring 1
Reverse the disassembly steps for installation

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY 2 Follow the left "Step" for removal.
Carburetor unit
1 Float chamber 1
2 Packing 1
3 Plunger rod 1
4 Rubber boot 1
5 Plunger 1
6 Spring 1
7 Circlip 1 NOt reusable
8 Ball 1
9 Float 1
10 Float pin 1

Step Procedure/Part name Q'ty Service points
11 Needle valve 1
12 Mainjet 1
13 Main nozzle 1
14 Pilotjet plug 1
15 Pilotjet 1
Reverse the disassembly steps for installation

SERVICE POINTS

Do not use a steel wire to clean the jets. This may enlarge the jet diameters and seriously affect performance.

Carburetor inspection

  1. Inspect.
  • Carburetor body

Cracks/damage -> Replace.

Contamination -> Clean.

  1. Inspect:
  • Mainjet

  • Pilotjet

  • Main nozzle

Contamination -> Clean.

  1. Inspect:
  • Needle valve

Grooved wear —> Replace.

  1. Inspect:
  • Float

Cracks/damage -> Replace.

Carburetor

  1. Install:
  • Needle valve

  • Float (1)

  • Float pin (2)

  • Screw (3)

• The float pin should fit into the slit in the carburetor and be retained with the screw.
• When installing the float into the carburetor, place the needle valve into the needle valve seat.
• After installation, make sure that the float operates smoothly.

  1. Measure:
  • Float height (a)

Out of specification -> Replace.

Float height: 10.0 ± 0.5 mm (0.39 ± 0.02 in)

• The float should be resting on the needle valve, but not compressing it.
• Take measurements at the midline of the float, opposite the side it pivots on. 4-9

Share on social:

Produtos Relacionados