Crowley Marine: serving boaters for over 40 years Crowley Marine: serving boaters for over 40 years
Parts in stock Most parts in stock Same day fulfillment
$3.95 shipping on all orders*
Low Price Guarantee
9.6 Pilot logo
0My cart

O-Ring & Seal Kit Trim / Tilt O-ring Kit-Outboard 0435567

Satisfaction rating 5 out of 5 (33 Ratings)
$79.95
Save $13.80 (15%)
5+ IN STOCK Ships Immediately

This product will be cross shipped from one of our secondary warehouses. Please note the additional handling time.

Last update: 43 days ago Update Now

  • Guaranteed fitment for 6 different models
  • This is an OEM part manufactured by Johnson/Evinrude, OMC
  • Flat rate shipping starting at $3.95
  • 30 day return policy

Product Description

Bombardier factory part. Search for more factory parts & parts diagrams.

1 Product Questions

R J

"O" ring kit #0435567, does each "O" ring come packaged separate with part # on it.

Answer:

The o rings are not packaged individually, they would all be together in the package. There would be a sheet included that will show what oring is what part.

by

by

by

50hp evinrude

Excellent quality and fast delivery received way before I expected ordered late on Friday and received on Monday
by

Everything from ordering to shipping was great
by

by

by

Johnson 50 HP

Repair Difficulty
Hard
Repair Time
2 to 4 hours
Shipping was fast. The installation of the kit did fix the leak.
by

Problem fixed: Power trim leak around shaft.

The cylinder leaked around the shaft. The top was very hard to break loose. It is 24 years old,and never apart. The rest of the job was not that hard. Replaced the seals and O rings. This has stopped the leak, and it is working fine.

Very dependable. I frequently make purchases from Crowley. Good prices and generally quick shipping
by

by

Johnson 50

Good. Got right part. Fast delivery
by

1989 evinrude 40

Repair Difficulty
Medium
Repair Time
1 to 2 hours
Great prices and quality parts.
by

Problem fixed: Tilt and trim leaked

Completely resealed my whole unit with this kit. Not the easiest but not hard either.

fast quick shipping. great parts list to go by.
by

Excellent.
by

by

40 h.p.Eve

Wonderful
by

Quick and easy
by

1990 50 HP Johnsone Tilt and trim leaking oil

Repair Difficulty
Medium
Repair Time
2 to 4 hours
Good. The salesperson got back to me on several occasions and assisted with my enquiries. Good service and above what one normally gets
by

Problem fixed: Oil leaking from shaft seal

Still doing it. Pump shaft extends and retracts when not under load. When fitted on the engine, retracts but wont lift. Still working on it.

by

by

Johnson 40 HP

by

Johnson 1999 50 HP

Repair Difficulty
Hard
Repair Time
1 to 2 hours
Speedy and complete, fixed my problem.
by

Problem fixed: tilt motor would not lift motor

Seal was leaking on top of lift cylinder, and other seals too. Because the tilt pump would not raise the motor, I opened bypass valve and raised the motor by hand to utmost position, propping motor up with supports. Removed pin from ram after removing position switch and retainer clip. Was able to use 1/4 " screw in end of pin to help remove pin. Did not have a slide hammer. Pushed ram down by hand and unscrewed cylinder end cap with spanner wrench. Removed ram from cylinder and took to shop. Removed nut on bottom of ram to remove ram rod from end cap so wiper seal could be replaced that was on end cap. Put in new seal and ring putting ring in first, then wiper/seal. Did the same on remaining seals and rings and replaced in cylinder housing. Replaced seals in tilt motor. Ran the tilt cylinder to fully extended position assisting by hand and filled with 10w-30 non-detergent oil. Retracted and extended again, each time filling with more oil for a total of probably 10 times before reservoir was full and lift would function properly. I used a syringe to fill with.

Fast, easy, a pleasure to do business with.
by

Experience was just as it should be.
by

Crowley has always been a top notch company to deal with.
by

by

1998 Johnson 35, J35QLECA

Repair Difficulty
Hard
Repair Time
More than 4 hours
by

Problem fixed: poor boat performance and leaking lift cylinder.

Examine motor installation for correct prop shaft alignment and adjust tilt tube pin to reduce the need to tilt motor up and take pressure off tilt cylinder. Replace o-rings and seals in tilt cylinder. Installed new water pump. Changed gearbox grease, hydraulic fluid, lubed steering cable, motor components and wheel bearings. Pins mounting tilt cylinder to motor and motor mount were difficult to remove due to corrosion and were cleaned. Test run required no tilt input for hole start or top end and an adjustment to correct torque steer to the left was applied. Boat is a Lowe 1405 and preforms very well.

Item came fast and as described. No problems, excellent experience.
by

I had an A+ experience.
by

Johnson 50Hp

Repair Difficulty
Medium
Repair Time
1 to 2 hours
by

Problem fixed: Leaking Tilt Cylinder

Remove seized pins, strip cylinder and fit seal kit, replace drive motor due to cracked housing

Detailed description and easy website . Fast delivery
by

by

different engine

very good experience with you repair easy fast shipping good price
by

Product Fitment Grid

This guide is to be used as a reference only. You must verify fitment using your model or serial number.

BRAND MODEL 1989 1990 1991 1992 1993
Evinrude Outboards 35 - - x x x
Evinrude Outboards 40 x x x x x
Evinrude Outboards 50 x x x x x
Johnson Outboards 35 - - x x x
Johnson Outboards 40 x x x x x
Johnson Outboards 50 x x x x x

Customers Also purchased

Supersession Chain

Name SKU Superceding SKU
O-Ring & Seal Kit VIEWING THIS PRODUCT 0435567 CURRENT
"O"-Ring Kit 0433816 0435567

Flat $3.95 Shipping on ALL parts orders

We offer shipping flat $3.95 shipping on ALL parts orders. (Complete Engines, Lower Units and Sterndrives excluded). In addition orders over $89 have reduced cost express shipping available in checkout.

shipping map shipping map legend

You can get a rough idea of standard transit times from the map above.