PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Service Manual Evinrude E-TEC G2 66°V6 2.7 L - Service Manual, P-N 5010056 Engine And Control Systems [Engine Management Module (Emm)]

Produits associés:
Service Manual Evinrude E-TEC G2 66°V6 2.7 L - Service Manual, P-N 5010056 Engine And Control Systems [Engine Management Module (Emm)]
5010056
BRP Marine

Engine Management Module (EMM)

The Engine Management Module (EMM) is a water-cooled controller. It controls engine management and engine–related remote control functions.

This section discusses the functions of the EMM and its various internal and external sensors. It also describes using Evinrude Diagnostics soft ware to retrieve and adjust service information saved in the EMM.

EMM Functions

The EMM controls the following processes and functions:

  • Alternator output; 55 V and 12 V

  • Start Assist Circuit (SAC) voltage boost

  • Fuel and ignition timing and duration

  • Fuel injector activation

  • Oil pump activation

  • Electric fuel lift pump control

  • Electric high pressure fuel pump control

  • Idle speed control

  • RPM limiter

  • Electrical circuit monitoring

  • Fault code creation and storage

  • Warning system activation

  • ROM verification, self-test

  • Cold starting

  • Output of diagnostic data

  • Tachometer signal

  • RPM profile and engine hours

  • Oil pump activation

  • Anti-knock compensation

  • Electronic throttle control

  • Electronic shift control

  • Dynamic Power Steering

EMM Connections

IMPORTANT: EMM connections and wiring must be clean and tight. Improper electrical connections can damage the EMM. DO NOT run the outboard with loose or disconnected wiring.

Make sure EMM connections are clean and tight.

  • Engine wire harness to EMM connectors; J1-A, J1-B, J2, J3, J4.

  • Stator to EMM connections; one 6-pin AMP and J2 connector.

  1. J1-A connector
  2. J1-B connector
  3. J2 connector
  4. J3 connector
  5. J4 connector

EMM Inputs and Outputs Diagram

  1. EMM

  2. 12 VDC Battery

  3. Fuel Vapor Separator

  4. Electronic Throttle Body

  5. Shift Actuator

  6. Knock Sensor (2)

  7. Engine Temperature Sensor (2)

  8. Exhaust Temperature Sender

  9. Trim Sender

10.Engine Oil Level Sender

11.Low Oil Switch

12.Digital Remote Control

13.Intake Air Temperature Sensor

14.Crankshaft Position Sensor

15.Trim Switch

16.Stator

17.DPS Pressure Sensors

18.Water in Fuel Sensor

19.Fuel Injector (6)

20.Ignition Coil (6)

21.Vapor Vent Solenoid

22.Digital Displays & Gauges

23.Oil Pumps

24.Dynamic Power Steering Module

25.Trim & Tilt Relay

26.Starter Solenoid & Motor

Share on social:

Produits associés