PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Service Manual DF40, DF50 Troubleshooting [77][Df40, Df50]

Produits associés:
Service Manual DF40, DF50 Troubleshooting [77][Df40, Df50]
99500-87J08-01E
Suzuki Marine

TROUBLESHOOTING

Before starting troubleshooting, read and follow the “PRECAUTION ON SYSTEM INSPECTION” section on page 3-33.

In this section, troubleshooting procedures are based on the assumption that “low pressure fuel system” and “mechanical components (power unit, lower unit, etc.)” are normal.

For troubleshooting of “Starter motor will not run”, see page 4-7.

CHART1 : SELF-DIAGNOSTIC CODE “3-4”

START

*CHART2 : SELF-DIAGNOSTIC CODE “4-2”**

START

• It will be possible to start engine if one CKP sensor has failed.
• No spark or injection signal will be supplied to the cylinder corresponding to the faild CKP sensor.

CHART3 : SELF-DIAGNOSTIC CODE “3-1”

START

CHART4 : SELF-DIAGNOSTIC CODE “2-4”
START

It will be possible to start engine if CMP sensor has failed.

CHART5 : SELF-DIAGNOSTIC CODE “2-2”

START

In this case, CTP switch will be in “always ON” condition.
(“D8” terminal voltage will be 0V always regardless throttle position.)

CHART6 : SELF-DIAGNOSTIC CODE “1-4”

START

CHART 7 : SELF-DIAGNOSTIC CODE “2-3”

START

CHART8 : SELF-DIAGNOSTIC CODE “3-2”

START

CHART9 : SELF-DIAGNOSTIC CODE “1-1”

START

This self-diagnostic code indication may be canceled by turning ignition switch
ON because ECM detects battery voltage.

It is difficult to check rectifier & regulator completely. Before replacing with new one, check if its ground point has good electrical contact.

CHART10 : SELF-DIAGNOSTIC CODE “1-5”

START

CHART11 : ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.
• Emergency stop switch plate is set in place.
• 15A fuse is good.

START

CHART12 : UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.

START

Possible cause :
• Incorrect by-pass air screw adjustment [NOTE3]
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose / silencer, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)

If neutral switch has failed (while engine running), engine will tend to stall when shifting into gear.
If neutral switch has failed as “always ON”, engine speed is limited to 3000 r/min by intermittent fuel injection and ignition timing is fixed at BTDC9 °.
If neutral switch has failed as “always OFF”, engine cannot be cranked.

If CTP switch has failed, engine will tend to stall when decelerating.

The self-diagnostic code “3-1” may not be indicated because IAC valve condition depends on ECM control. (See page 3-28.)
If IAC valve has failed, “Fast-idle function (warm-up mode)” won’t operate.

Share on social:

Produits associés