PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Service Manual DF40, DF50 Troubleshooting [238][Df40, Df50]

Produits associés:
Service Manual DF40, DF50 Troubleshooting [238][Df40, Df50]
99500-87J08-01E
Suzuki Marine

TROUBLESHOOTING

Before starting troubleshooting, read and follow the “PRECAUTION ON SYSTEM INSPECTION” section on page 13-33.

In this section, troubleshooting procedures are based on the assumption that “low pressure fuel system” and “mechanical components (power unit, lower unit, etc.)” are normal.

For troubleshooting of “Starter motor will not run”, see page 4-7 in Service Manual P/N. 99500-87J0(cid:127)-01E.

CHART1 : SELF-DIAGNOSTIC CODE “3-4”

START

CHART2 : SELF-DIAGNOSTIC CODE “4-2”

START

• It will be possible to start engine if CKP sensor has failed.

CHART3 : SELF-DIAGNOSTIC CODE “3-1”

START

CHART4 : SELF-DIAGNOSTIC CODE “2-4”

START

It will be possible to start engine if CMP sensor has failed.

CHART5 : SELF-DIAGNOSTIC CODE “2-2”

START

In this case, CTP switch will be in “always ON” condition. (“24” terminal voltage will be 0V always regardless throttle position.)

CHART6 : SELF-DIAGNOSTIC CODE “1-4”

START

CHART 7 : SELF-DIAGNOSTIC CODE “2-3”

START

CHART8 : SELF-DIAGNOSTIC CODE “3-2”

START

CHART9 : SELF-DIAGNOSTIC CODE “1-1”

START

This self-diagnostic code indication may be canceled by turning ignition switch ON because ECM detects battery voltage.

It is difficult to check rectifier & regulator completely. Before replacing with new one, check if its ground point has good electrical contact.

CHART10 : SELF-DIAGNOSTIC CODE “1-5”

START

CHART11 : SELF-DIAGNOSTIC CODE “4-3"

START

CHART12 : ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)

START

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.
• Emergency stop switch plate is set in place.

CHART13 : UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.

START

If neutral switch has failed (while engine running), engine will tend to stall when shifting into gear. If neutral switch has failed as “always ON”, engine speed is limited to 3000 r/min by intermittent fuel injection and ignition timing is fixed at BTDC9 °. If neutral switch has faild as “always OFF”, engine cannot be cranked>

If CTP switch has failed, engine will tend to stall when decelerating.

: The self-diagnostic code “3-1” may not be indicated because IAC valve condition depends on ECM control. (See page 13-28.) If IAC valve has failed, “Fast-idle function (warm-up mode)” won’t operate.

Share on social:

Produits associés