PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Service Manual 5009011_200–300 HP 90°V Models AA Gearcase [Gearcase Assembly 2]

Produits associés:
Service Manual 5009011_200–300 HP 90°V Models AA Gearcase [Gearcase Assembly 2]
5009011
BRP Marine

Water Intake Screens

Water Intake Screens

Install water intake screens. Tighten screws to a torque of 60 to 84 in. lbs. (7 to 9.5 N•m).

006886

  1. Water intake screen

Shift Housing, Gear, and Propeller Shaft Installation

Push shifter detent into farthest downward position. Tip the rear of the gearcase slightly down ward to assist in the installation of the shaft assembly.

Be sure the thrust bearing and the thrust washer are in the proper position. Insert the shaft assembly fully into the gearcase while aligning shift housing pin with hole in forward end of gearcase housing.

006929

  1. Pin

Shift Rod Cover

Refer to Shift Rod Housing Installation on p. 313

Pinion Gear and Driveshaft Installation

Refer to Pinion Gear and Driveshaft Installation on p. 314.

Propeller Shaft Bearing Housing and Gear Installation

IMPORTANT: The propeller shaft bearing housing on “M2” type gearcases is PRESSED into the gearcase housing.

Lightly apply Triple Guard Grease to new bearing housing O-rings. Install O-rings in grooves in the housing. Grease the machined side surfaces of bearing housing.
Place bearing housing in gearcase.

006846

Align retaining holes in bearing housing with screw holes in gearcase. Thread Alignment Pins, P/N 354140, into gearcase.

006926

  1. Alignment pins

IMPORTANT: To align pinion, clutch dog and forward gears turn driveshaft clockwise while installing propeller shaft bearing housing. Gears MUST align for bearing housing to seat completely.

Use Installer Handle, P/N 345822, Propeller Shaft Bearing Housing Installer, P/N 354057, Gearcase Fixture, P/N 354059 and an appropriate floor press (10 ton or greater) to install housing into gearcase. Align and level gearcase assembly in fixture as shown. Secure fixture to floor press.

006927

  1. Gearcase fixture, P/N 354059
  2. Vertical alignment screws
  3. Handle P/N 345822
  4. Housing installer P/N 354057

Housing must be completely seated in gearcase to install retainer screws. Bearing housing is approximately level with gearcase.

006928

Apply Ultra Lock to threads and install two retaining screws. Tighten screws to a torque of 18 to 20 ft. lbs. (24 to 27 N•m).

006835

  1. Retainer screws

Final Assembly and Adjustment

To complete gearcase assembly, refer to:
• GEARCASE LEAK TEST on p. 289
• WATER PUMP SERVICE on p. 293
• SHIFT ROD ADJUSTMENT on p. 296
• GEARCASE REMOVAL AND INSTALLATION on p. 290
• Gearcase Lubricant on p. 39
• Propeller Hardware Installation on p. 288
• Trim Tab Adjustment on p. 32

During break-in period of a reassembled gearcase, change the gearcase lubricant between 10 to 20 hours of operation.

Share on social:

Produits associés