PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Service Manual 5007215_Evinrude E-TEC 200-250 HP Electrical And Ignition [Spark Plugs]

Produits associés:
Service Manual 5007215_Evinrude E-TEC 200-250 HP Electrical And Ignition [Spark Plugs]
5007215
BRP Marine

ELECTRICAL AND IGNITION

If the pointer alignment is NOT correct, rotate the flywheel clockwise to align the mark “C” with the pointer. Hold the flywheel in this position. Loosen the pointer retaining screw and adjust the pointer location to align with the cast-in TDC boss on the flywheel. Tighten retaining screw.

Install spark plugs. Refer to Spark Plug Indexing on p. 155.

Timing Verification

Use the Evinrude Diagnostics Software program to synchronize the mechanical timing of the out board with the electronic timing control function of the EMM.

Timing Adjustment Screen

Perform timing verification after any of the following procedures:

  • Powerhead replacement
  • Crankshaft replacement
  • Flywheel removal or replacement
  • CPS replacement
  • EMM replacement
  • EMM software replacement (reprogramming)

Make sure the timing pointer is set and the outboard reaches operating temperature before timing verification is performed.

SPARK PLUGS

Inspection

Spark plugs should be removed and examined periodically. Replace worn, fouled or damaged spark plugs.

Use only recommended spark plugs with the cor rect gap setting.

Spark Plug, Champion
QC10WEP @ 0.028 ± 0.003 in. (0.76 mm)
  • Remove spark plugs and inspect condition.
  • Set spark plug gap on new, replacement spark plugs.
  • Mark spark plugs for ground electrode orientation.
  • Apply Electrical Grease to the ribbed portion of the spark plug ceramic and to the opening of the spark plug cover to prevent corrosion.
  • Install spark plugs using “indexing” procedure.

Indexing

Spark plug indexing positions the ground electrode of the spark plug opposite the fuel injector nozzle.

Put an ink mark on the ceramic of the spark plug that is in line with the OPEN side of the ground electrode. This mark will be used to orient the spark plug with the OPEN side of the ground electrode facing the fuel injector.

  1. Ink mark
  2. Open side

Apply Triple-Guard grease to the gasket surface of the spark plugs. Install all spark plugs and tighten them to a torque of 15 ft. lbs. (20 N-m).

If the mark is in unshaded area do not tighten any more.

Spark Plug Indexing Diagram

  1. Unshaded area
  2. Shaded area

If the mark is in the shaded area, reset torque wrench to 30 ft. lbs. (41 N-m) and continue to turn until the mark is in the unshaded area.

If the mark does not reach the unshaded area before the torque of 30 ft. lbs. (41 N-m) is reached, the spark plug cannot be indexed for that cylinder. Try another spark plug and repeat the steps above.

ELECTRIC STARTER SERVICING

Removal

Do not clean the starter drive while the starter motor and drive are installed on the powerhead. The cleaning agent could drain into the starter motor, washing dirt from the drive into the starter bearings and commutator.

Disconnect the battery cables at the battery. Remove the starter positive (+) cable.

Remove the four frame and bracket mounting screws. Lift and remove the starter.

Loosen the two nuts used to fasten the starter bracket. Remove the nuts and bracket.

Share on social:

Produits associés