EMM LED INDICATORS
The EMM LED indicators provide a quick refeence to the status of several outboard systems. Checking the LEDs FIRST when diagnosing an engine problem can save a lot of time.
IMPORTANT: LED 1 is toward the rear of the outboard (Closest to EMM J2 connector).
- LED indicators
Key ON
When the EMM is ON (engine not running), the following LEDs should light:
LED 1 – SAC Circuit working – 30 V present on 55 V circuit.
LED 3 – Sensor Circuits working. FLASHING LIGHT indicates Code 57 – engine will not start.
LED 4 – Stop Circuit not grounded–okay to start. FLASHING LIGHT indicates severe overheat or no oil – engine in SHUTDOWN mode.
Starting
Starting mode occurs from the time the flywheel begins to turn until the outboard is running for 2 seconds. During starting, all four LEDs should light and then go off in sequence.
LED 1 – CHARGING OKAY – Stator signal 30 V or higher. For NO LIGHT, check for:
- SAC circuit problem
LED 2 – CRANK POSITION OKAY – input from CPS, EMM powered ON. For NO LIGHT, check for:
- Code 16 – CPS, intermittent loss of sync
LED 3 – SENSORS OKAY (5 V). For NO LIGHT, check for:
Code 12 – TPS circuit fault
Code 13 – TPS below expected range
Code 14 – TPS above expected range
Code 19 – In Gear (tiller models)
Code 23 – EMM temp. sensor circuit fault
Code 24 – EMM temp. below expected range
Code 37 – Water in fuel
Code 41 – PORT temp. sensor circuit fault
Code 42 – PORT temp. below expected range
Code 47 – AT sensor circuit fault
Code 48 – AT sensor below expected range
Code 49 – AT sensor above expected range
Code 58 – Operating temp. not reached, Port
Code 59 – Operating temp. not reached, Stbd
Code 67 – STBD temp. sensor circuit fault
Code 68 – STBD temp. below expected range For FLASHING LIGHT, check for Code 57.
LED 4 – LANYARD/STOP OKAY. For NO LIGHT, check for:
- Grounded stop circuit.
For FLASHING LIGHT, check for:
Code 29 – EMM temp. OVER range (flashing)
Code 31 – Engine temp. OVER range (flashing)
Code 33 – Engine shutdown, excessive no oil condition
Running
When the outboard is running, all of the LEDs should be off. If a light is on, check for:
LED 1 – CHARGING FAULT:
Code 17 – System voltage (55 V) below range
Code 18 – System voltage (55 V) above range
Code 26 – Low battery (12 V) voltage
Code 27 – High battery (12 V) voltage
Code 77 – SAC overcurrent fault
LED 2 – INJECTOR/IGNITION FAULT:
Code 51 – No. 1 injector circuit open
Code 52 – No. 2 injector circuit open
Code 53 – No. 3 injector circuit open
Code 54 – No. 4 injector circuit open
Code 55 – No. 5 injector circuit open
Code 56 – No. 6 injector circuit open
Code 61 – No. 1 injector circuit short
Code 62 – No. 2 injector circuit short
Code 63 – No. 3 injector circuit short
Code 64 – No. 4 injector circuit short
Code 65 – No. 5 injector circuit short
Code 66 – No. 6 injector circuit short
Code 81 – No. 1 ignition primary circuit open
Code 82 – No. 2 ignition primary circuit open
Code 83 – No. 3 ignition primary circuit open
Code 84 – No. 4 ignition primary circuit open
Code 85 – No. 5 ignition primary circuit open
Code 86 – No. 6 ignition primary circuit open
Code 91 – Fuel pump circuit open
Code 92 – Exhaust valve circuit open
Code 94 – Fuel pump circuit short
LED 3 – Sensor circuits (5 V), “SENSOR FAULT.” For LIGHT ON, check for possible fault codes:
Code 12 – TPS circuit fault
Code 13 – TPS below expected range
Code 14 – TPS above expected range
Code 16 – CPS, intermittent loss of sync
Code 23 – EMM temp. sensor circuit fault
Code 24 – EMM temp. below expected range
Code 37 – Water in fuel
Code 41 – PORT temp. sensor circuit fault
Code 42 – PORT temp. below expected range
Code 47 – AT sensor circuit fault
Code 48 – AT sensor below expected range
Code 49 – AT sensor above expected range
Code 57 – high RPM with low TPS setting
Code 58 – PORT operating temp. not reached
Code 59 – STBD operating temp. not reached
Code 67 – STBD temp. sensor circuit fault
Code 68 – STBD temp. below expected range
Code 71 – oil pressure circuit fault detected
Code 72 – oil pressure below expected range
Code 73 – oil pressure above expected range
Code 74 – water pressure circuit fault detected
Code 75 – water pressure below range
Code 76 – water pressure above range
Code 78 – analog 5V circuit overload detected
Code 79 – starter solenoid circuit open
Code 87 – exhaust pressure circuit fault
Code 88 – exhaust pressure below range
Code 89 – exhaust pressure above range
- Code 97 – Intermittent switched B+ detected
LED 4 – Engine overheat, EMM temperature or sensor, oil injection pump or sensor, “NO OIL / OVERHEAT.” For LIGHT ON, check for possible fault codes:
Code 25 – EMM temp. above expected range
Code 29 – EMM temp. OVER range (flashing)
Code 31 – engine temp. OVER range (flashing)
Code 33 – excessive NO OIL faults
Code 34 – oil injection pump circuit open
Code 38 – oil pressure feedback not detected
Code 43 – PORT temp. above expected range
Code 69 – STBD temp. above expected range
