PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Power Unit [Power Unit Removal And Installation] [2002]

Produits associés:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1996 - 2002 5hp All
Yamaha Outboard 1996 - 1999 4hp All

Power Unit [Power Unit Removal And Installation] [2002]
LIT-18616-01-33
Yamaha Marine

PREPARATION FOR REMOVAL

  • Remove the top cowling.
  • Remove the fuel tank and hose. Refer to the “FUEL SYSTEM” section in CHAPTER 4.
  • Remove the carburetor.
    Refer to the “FUEL SYSTEM” section in CHAPTER 4.

NOTE ON REMOVAL AND REASSEMBLY

Extent of removal: (1) Power unit removal

  • Clean all dirt, mud, dust and foreign material from the engine before the engine is removed and disassembled.
  • To ensure that you can perform the work cleanly and efficiently, check that you have the proper tools and cleaning equipment before commencing engine removal and reassembly.

REMOVAL POINTS

Start-in-gear protection wire (For start-in-gear protection model)

  1. Remove:
    • Clip (1)
    • Link (2)

Stop switch/Engine stop switch lead

  1. Remove:
    • Black (B) lead (1) (ground lead)
  2. Disconnect:
    • White (W) lead (2)
  3. Remove:
    • Stop switch (3)

Ignition coil bracket

  1. Remove:
    • Bolt (1)
    • Spark plug cap (2)
    • Ignition coil bracket (3)

ASSEMBLY AND INSTALLATION

Always use new gaskets, oil seals and O-rings. The use of any used oil seal or O-ring may result in oil leakage due to invisible scratches or stretches.
Apply grease to parts where specified.

Power unit

  1. Apply:
    • Gasket Maker
      Onto both faces of the gasket.

Clean the contacting surfaces of crankcase and bottom cowling.

  1. Install:
    • Dowel pin (1)
    • Gasket (2) (new)

  1. Install:
    • Power unit (1)

Insert the drive shaft into the crankshaft. If the splines will not come in complete mesh, rotate the crankshaft a little so that they are in mesh correctly.

  1. Install:
    • Mount bolt (1)
    • Mount bolt (2)

Tighten the bolts in two steps of torque.

Mount bolt:
1st : 3 Nm (0.3 kg•m, 2.2 ft•lb)
2nd : 8 Nm (0.8 kg•m, 5.8 ft•lb)

  1. Install:
    • Stop switch/Engine stop switch (1)
    • White lead (2)
    • Black lead (3)
  1. Install:
    • Link (1)
    • Clip (2)
  1. Adjust:
    • Throttle wire
      Refer to the “PERIODIC SERVICE" section in CHAPTER 3.
  1. Adjust:
    • Idle speed
      Refer to the “PERIODIC SERVICE” section in CHAPTER 3.
Share on social:

Produits associés