PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Owner's Manual DF350A Propeller Selection, Installation And Removal

Produits associés:
Owner's Manual DF350A Propeller Selection, Installation And Removal
99011-98L30-03B
Suzuki Marine

Owner's Manual

  1. After the passcode confirmation is completed, turn the main switch to the position and then release it. The main switch automatically returns to the position. The Keyless Start System turns OFF and the passcode indication stops.

PROPELLER SELECTION, INSTALLATION AND REMOVAL

PROPELLER SELECTION

It is essential to use a propeller on your outboard motor that is properly matched to your boat’s operating characteristics. The speed of the engine when you operate your boat at full throttle depends on the propeller you use. Excessive engine speed can seriously damage the motor, while low engine speed at full throttle will adversely affect the performance. Your operating load will also affect propeller selection. Smaller loads generally require larger pitch propellers; larger loads generally require smaller-pitch propellers. Your authorized Suzuki Marine Dealer will assist you in selecting a suitable propeller for your boat.

Installing a propeller with either too much or too little pitch will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Consult your authorized Suzuki marine dealer to assist you in selecting a suitable propeller for your boat.

You can determine if your propeller is appropriate for use with your boat by using a tachometer to measure engine speed when operating your boat at full throttle, under minimum load conditions. If you are using an appropriate propeller, the engine speed will be within the following range:

DF350A 5700 - 6300
r/min. (min–¹)

If the engine speed is not within this range, consult your authorized Suzuki Marine Dealer to determine which propeller size is best for you.

If you change propellers, be sure to perform the above check again, to confirm that the engine speed under full throttle is within the specified range.

PROPELLER INSTALLATION AND REMOVAL

Failure to take proper precautions when installing or removing the propeller can result in severe personal injury.
When installing or removing the propeller:
• Always shift into “Neutral” and remove the emergency stop switch lock plate so that the motor cannot be started accidentally.
• Wear gloves to protect hands, and “lock” the propeller by placing a block of wood between the blades and the anti-cavitation plate.

Using the improper combination of front and rear propellers can cause lower unit damage.
Confirm the size of the front and rear propellers when installing them. The front and rear propellers must be the same number of blades, diameter and pitch.

The propeller size is indicated as follows. The first character shows the No. of blades, then the following characters show the diameter and pitches in this order. The last character “F” or “R” shows the installation position.

F: Front R: Rear

Example: 3X15-1/2X25.5F

Propeller installation

To install the propeller on your outboard motor, use the following procedure:

  1. Coat the propeller shaft splines (1) liberally with Suzuki water resistant grease to help prevent corrosion.

  2. Place the front propeller stopper (2) on the shaft.

  1. Align the front propeller 3 with the propeller shaft splines and slide the front propeller onto the shaft.

  2. Place the front propeller nut spacer (4) and front propeller nut stopper 5 on the shaft.

Align section (A) of the stopper (5) with the punch mark (C) of the spacer (4) and attach it.

  1. Install the front propeller nut 6 and tighten it with a torque wrench to 125 – 135 N·m (12.5 – 13.5 kg-m/90.4 – 97.6 lb-ft).

• Front propeller nut is left hand thread.
• For removing or installing the front propeller nut, the “Propeller nut remover & installer” (Suzuki genuine part), is required. Consult your authorized Suzuki marine dealer for Suzuki genuine parts.
• Align the locking edge of the stopper 5 with the groove on the front propeller nut.

  1. Bend the locking edge of the front propeller nut stopper (5) to the front propeller nut side to secure the nut.

• Do not bend section (A) and (B) of the front propeller nut stopper (5) to the front propeller nut side.
• Bend two sections of the locking edge of the front propeller nut stopper (5).

  1. Place the rear propeller stopper (7) on the shaft.

  2. Align the rear propeller (8) with the propeller shaft splines and slide the rear propeller onto the shaft.

  3. Place the rear propeller nut spacer (9) and washer (10) on the shaft.

  4. Install the rear propeller nut (11) and tighten it with a torque wrench to 50 – 60 N·m (5.0 – 6.0 kg-m/36.0 – 43.5 lb-ft).

  5. Align the grooves in the rear propeller nut with the hole in the shaft, then insert a cotter pin (12) and bend the pin ends over to lock it in place.

Propeller removal

To remove the propeller on your outboard motor, use the following procedure.

  1. Shift to “NEUTRAL” position.

  2. Remove the cotter pin (1) from the rear propeller nut and remove the rear propeller nut (2).

  3. Remove the washer (3), spacer (4), rear propeller (5) and rear propeller stopper (6) from the propeller shaft.

  1. Straighten the locking edges on the front propeller nut stopper (7) from the front propeller nut and remove the front propeller nut (8).

• Front propeller nut is left hand thread.
• For removing or installing the front propeller nut, the “Propeller nut remover & installer” (Suzuki genuine part), is required. Consult your authorized Suzuki marine dealer for Suzuki genuine parts.

  1. Remove the front propeller nut spacer (9), front propeller (10) and front propeller stopper (11) from the propeller shaft.

Share on social:

Produits associés