PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Lower Unit [Backlash(Regular Rotation Model)] [2008]

Produits associés:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 2003 - 2005 200hp All
Yamaha International 2003 - 2005 225hp All
Yamaha International 2003 - 2005 200hp All
Yamaha Outboard 2003 - 2005 225hp All

Lower Unit [Backlash(Regular Rotation Model)] [2008]
LIT-18616-02-76
Yamaha Marine

Measuring the forward and reverse gear backlash

  1. Remove the water pump assembly.

  2. Set the gearshift to the neutral position.

Shift rod push arm: YB-06052

  1. Install the special service tool so that it pushes against the propeller shaft.

NOTE:

Tighten the universal puller or center bolt while turning the drive shaft until the drive shaft can no longer be turned.

Bearing housing puller (1): YB-06207
Universal puller (2): YB-06117

  1. Install the backlash indicator onto the drive shaft (22.4 mm [0.88 in] in diameter), then the dial gauge onto the lower unit.

  2. Set the lower unit upside down.

NOTE:
Install the dial gauge so that the plunger (a) contacts the mark (b) on the backlash indicator.

Backlash indicator gauge (3): YB-06265
Magnetic plate (4): YB-07003
Dial gauge (5): YU-03097
Magnet flexible stand (6): YU-34481

  1. Slowly turn the drive shaft clockwise and counterclockwise and measure the backlash when the drive shaft stops in each direction.

Forward gear backlash: 0.21-0.44 mm (0.008-0.017 in)

  1. Add or remove shim(s) if out of specification.
Forward gear backlash Shim thickness
Less than 0.21 mm (0.008 in) To be decreased by (0.33- M) x 0.71
More than 0.44 mm (0.017 in) To be increased by (M-0.33) x 0.71

  M: Measurement

  Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools from the propeller shaft.

  2. Apply a load to the reverse gear by installing the propeller (7), the spacer (8) (without the washer (9)), then the washer (10) as shown.

NOTE:

Tighten the propeller nut (11) while turning the drive shaft until the drive shaft can no longer be turned.

  1. Slowly turn the drive shaft clockwise and counterclockwise and measure the backlash when the drive shaft stops in each direction.

Reverse gear backclash: 0.70-1.03 mm (0.028-0.041 in)

  1. Add or remove shim(s) if out of specification.
Reverse gear backlash Shim thickness
Less than 0.70 mm (0.028 in) To be decreased by (0.87- M) x 0.71
More than 1.03 mm (0.041 in) To be increased by (M-0.87) x 0.71

  M: Measurement

  Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools, and then install the water pump assembly.
Share on social:

Produits associés