PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Fuel System [Carburetor] [2008]

Produits associés:

Applicable Models

Model group Year Model Serial
Yamaha International 2001 - 2005 4hp All
Yamaha Outboard 1999 - 2005 4hp All

Fuel System [Carburetor] [2008]
LIT-18616-01-79
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for disassembly.
Carburetor assembly
(1) Screw with washer 3
(2) Carburetor top cover 1
(3) Gasket (carburetor top cover) 1
(4) Plug 1
(5) Screw with washer (float chamber) 2
(6) Float chamber 1
(7) O-ring 1
(8) Float pin 1

EXPLODED DIAGRAM

Step Procedure/Part name Q'ty Service points
(9) Float 1
(10) Needle valve 1
(11) Plug 1
(12) Main nozzle 1
(13) Main jet 1
(14) Pilot jet 1
(15) Pilot screw 1 Except for USA
Reverse the disassembly steps for assembly.

SERVICE POINTS

Carburetor removal

  1. Remove:
    • Float pin (1)
    • Float (2)
    • Needle valve

When removing the float pin (1), tap it in arrow direction (4) from pivot of the pipe joint side (3) as shown.

Carburetor inspection

Do not use a steel wire to clean the jets. This may enlarge the jet diameters and seriously affect performance.

  1. Inspect:
    • Carburetor body
      Cracks/damage ➝ Replace.
      Contamination ➝ Clean.
  2. Inspect:
    • Main jet
    • Pilot jet
    • Main nozzle
      Contamination ➝ Clean.

  1. Inspect:
    • Needle valve
    • Pilot screw (Except for USA)
        Grooved wear ➝ Replace.
  2. Inspect:
    • Float
        Cracks/damage ➝ Replace.

  1. Inspect:
    • O-ring
        Wear/cracks/damage ➝ Replace.

Carburetor installation

  1. Install:
    • Needle valve (3)
    • Float (1)
    • Float pin (2)

• When setting the float (1) into the carburetor, hock the needle valve (3) into the float and insert the needle valve seat.
• When installing the float pin (2), tap the float pin in arrow direction (4) to the pivot of the pipe joint side (5) as shown.
• After installation, make sure that the float operates smoothly.

  1. Measure:
    • Float height (a)
      Out of specification ➝ Replace

Float height : 18.0 ~ 19.0 mm (0.71 ~ 0.75 in)

• Make sure to tilt the carburetor ass'y clockwise 45° for needle valve with spring no load, when measuring the float height.
• Take measurement at the side end of the float, as shown.

Share on social:

Produits associés