PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Fuel System [Carburetor] [1998]

Produits associés:

Applicable Models

Model group Year Model Serial
Yamaha International 1998 25hp All
Yamaha Outboard 1998 25hp All

Fuel System [Carburetor] [1998]
LIT-18616-01-77
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY 1 Follow the left "Step" for removal.
Carburetor unit
1 Throttle link rod 1
2 Electrothermal ram retainer 1
3 Electrothermal ram 1
4 O-ring 1
5 Carburetor top cover 1
6 Gasket 1
7 Pilot outletjet 1
8 O-ring 1
9 Throttle stop screw 1
10 Spring 1
Reverse the disassembly steps for installation

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY 2 Follow the left "Step" for removal.
Carburetor unit
1 Float chamber 1
2 Packing 1
3 Plunger rod 1
4 Rubber boot 1
5 Plunger 1
6 Spring 1
7 Circlip 1 NOt reusable
8 Ball 1
9 Float 1
10 Float pin 1

Step Procedure/Part name Q'ty Service points
11 Needle valve 1
12 Mainjet 1
13 Main nozzle 1
14 Pilotjet plug 1
15 Pilotjet 1
Reverse the disassembly steps for installation

SERVICE POINTS

Do not use a steel wire to clean the jets. This may enlarge the jet diameters and seriously affect performance.

Carburetor inspection

  1. Inspect.
  • Carburetor body

Cracks/damage -> Replace.

Contamination -> Clean.

  1. Inspect:
  • Mainjet

  • Pilotjet

  • Main nozzle

Contamination -> Clean.

  1. Inspect:
  • Needle valve

Grooved wear —> Replace.

  1. Inspect:
  • Float

Cracks/damage -> Replace.

Carburetor

  1. Install:
  • Needle valve

  • Float (1)

  • Float pin (2)

  • Screw (3)

• The float pin should fit into the slit in the carburetor and be retained with the screw.
• When installing the float into the carburetor, place the needle valve into the needle valve seat.
• After installation, make sure that the float operates smoothly.

  1. Measure:
  • Float height (a)

Out of specification -> Replace.

Float height: 10.0 ± 0.5 mm (0.39 ± 0.02 in)

• The float should be resting on the needle valve, but not compressing it.
• Take measurements at the midline of the float, opposite the side it pivots on. 4-9

Share on social:

Produits associés