PRÉPAREZ-VOUS POUR L'HIVER : de 10 % à 50 % de réduction sur toutes les pièces d'origine !

Sauf interdiction par le fabricant. N'inclut pas les produits de rechange ou de marque Crowley Marine. Prix indiqué.

Nos entrepôts sont fermés le jeudi 26 et le vendredi 27 novembre. Joyeuse fête de Thanksgiving des États-Unis!

Recherche Plus d'un 1 million de pièces d'équipementier
Facile à utiliser  schémas des pièces Meilleur prix  garanti Assistance en directexperte   Plus de 50 ans  au service des plaisanciers Grand choix de pièces OEM  -  de 1950 à 2026 La plupart des pièces en stock  -  Exécution le jour même
Pièces en stock- Exécution le même jour

Bracket Unit [Tiller Handle (F50:F50A, T50:Ft50B)] [2004]

Produits associés:

Applicable Models

Model group Year Model Serial
Yamaha International 2004 60hp All
Yamaha Outboard 2004 60hp All

Bracket Unit [Tiller Handle (F50:F50A, T50:Ft50B)] [2004]
LIT-18616-FT-60
Yamaha Marine

Tiller handle (F50/F50A, T50/FT50B)

No. Part name Q’ty Remarks Tightening torques
Stage
Tightening torques
N•m
Tightening torques
kgf•m
Tightening torques
ft•lb
1 Tiller handle assembly 1
2 Friction plate 1
3 Tiller handle wiring harness 1
4 Tiller handle wiring 1 Models applicable for harness tachometer, trim meter or warning buzzer
5 Grommet 1
6 Clip 1
7 Throttle cable 1
8 Plate 1
9 Bolt 3 M6 x 20 mm
10 Bolt 1 M8 x 16 mm 9 0.9 6.5
11 Negative battery lead 1
12 Cable guide 1
13 Grommet 1
14 Nut 1 7 0.7 5.1
15 Washer 1
16 Positive battery lead 1
17 Connector 1
18 Clip 1
19 Shift cable 1
20 Plastic tie 2
21 Cover 1
22 Screw 3 M6 x 35 mm
23 Trailer switch coupler 1
24 PTT switch coupler 1 Models with trailer switch
25 Bolt 1 M6 x 35 mm
26 Screw 1 M6 x 25 mm
27 Collar 1
28 Clamp 1
29 Nut 2 37 3.7 27
30 Bolt 2 M6 x 16 mm

No. Part name Q’ty Remarks Tightening torques
Stage
Tightening torques
N•m
Tightening torques
kgf•m
Tightening torques
ft•lb
31 Nut 2
32 Collar 2
33 Bolt 2 M8 x 50 mm
34 Self-locking nut 1
35 Bracket 1
36 Steering lock shaft 1
37 Steering lock knob 1
38 Friction plate 1
39 Friction piece 2

No. Part name Q’ty Remarks Tightening torques
Stage
Tightening torques
N•m
Tightening torques
kgf•m
Tightening torques
ft•lb
1 Tiller handle sub assembly 1
2 Screw 2 M6 x 10 mm
3 Shift lever cover 1
4 Bolt 1 M8 x 40 mm
5 Shift lever 1
6 Bushing 1
7 Washer 1
8 Bushing 2
9 Nut 1 4 0.4 2.9
10 Engine stop lanyard switch 1
11 Nut 1 38 3.8 27
12 Washer 1
13 Bracket 1
14 Collar 1
15 Wave washer 1
16 Washer 1
17 Bolt 1
18 Clamp 1
19 Screw 1
20 Connector 2
21 Engine start switch housing 1
22 Engine start switch 1
23 Nut 1 5 0.5 3.7
24 Bolt 1 M6 x 25 mm
25 Screw 1
26 Bolt 1 M6 x 20 mm
27 Cover 1
28 Power trim and tilt switch 1
29 Screw 5 M6 x 16 mm
30 Screw 2 M6 x 16 mm

No. Part name Q’ty Remarks Tightening torques
Stage
Tightening torques
N•m
Tightening torques
kgf•m
Tightening torques
ft•lb
31 Screw 2 M6 x 40 mm
32 Throttle grip 1
33 Screw 1 M5 x 25 mm
34 Washer 1
35 Spring 1
36 Bushing 1

No. Part name Q’ty Remarks Tightening torques
Stage
Tightening torques
N•m
Tightening torques
kgf•m
Tightening torques
ft•lb
1 Tiller handle 1
2 Cotter pin 1 Not reusable
3 Friction adjusting knob 1
4 Grommet 1
5 Plastic tie 1
6 Cable clamp 1
7 Stay 1
8 Bolt 1 M6 x 14 mm
9 Throttle cable 1 Short
10 Clip 1
11 Throttle arm 1
12 Throttle arm shaft 1
13 Shift cable 1 Long
14 Shift cable bracket 1
15 Bolt 1 M6 x 14 mm
16 Clip 1
17 Frame 1
18 Screw 2 M5 x 14 mm
19 Bolt 1 M6 x 14 mm
20 Spring housing 1
21 Spring 1
22 Actuator 1
23 Roller 1
24 Bushing 1
25 Shift arm 1
26 Bolt 2 M6 x 30 mm
27 Throttle shaft 1
28 Friction piece 1
29 Nut 1

Checking the throttle cable and shift cable

  1. Check the operation of the throttle cable and shift cable.

  2. Check the inner wire and outer wire of both cables for bends or damage, and the rubber seals for damage. Replace if necessary.

Assembling the tiller handle

  1. Install the throttle shaft (1) and throttle arm (2) into the frame (3). Align the mark (a) of the fully closed position of the throttle shaft to the shaft holder. Align the mark (b) of the fully closed position of the throttle arm to the indent of the frame.

Make sure that the throttle grip is fully closed when installing the throttle cable.

Share on social:

Produits associés