¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Specifications [Maintenance Specifications] [1998]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 1998 25hp All
Yamaha Outboard 1998 25hp All

Specifications [Maintenance Specifications] [1998]
LIT-18616-01-77
Yamaha Marine

MAINTENANCE SPECIFICATIONS

Engine

Item-Worldwide/USA/Canada Unit Model
F20A   F25A
-   F25W
-   F25W
CONNECTING ROD(S)
    Small end inside diameter mm (in) 15.985 ~ 15.998 (0.6293 ~ 0.6298)
    Big end oil clearance mm (in) 0.020 ~ 0.052 (0.0008 ~ 0.0020)
    Connecting rod inside diameter A: Blue B: Black C: Brown
CRANKSHAFT
    Crankshaft outside diamete mm (in) 42.984 ~ 43.000 (1.692 ~ 1.693)
    Main journal clearance mm (in) 0.012 ~ 0.044 (0.0005 ~ 0.0017)
    Crankcase mark - bearing color A: Blue, B: Black, C: Brown
    Crankshaft big end side clearance mm (in) 0.05 ~ 0.22 (0.002 ~ 0.009)
    Crankshaft journal clearance mm (in) 0.020 ~ 0.052 (0.0008 ~ 0.0020)
    Runout limit (B) mm (in) 0.03 (0.0012)
BALANCER
    Balancer piston diameter mm (in) 94.893 (3.7360)
    Crankcase balancer cylinder mm (in) 95.018 (3.7409)
    inside diameter
    Connecting rod inside diameter 68.049 (2.6791)
THERMOSTAT
    Valve opening temperature °C (°F) 60 (140)
    Full-open temperature °C (°F) 70 (158)
    Valve lift mm (in) 3 (0.12)
FUEL PUMP
    Discharge LIUS gal, lmpgal)/h@6,000 r/min 70 (18.5, 15.4)
    Pressure kPa (kg/cm2, psi) 20 ~ 40 (0.2 ~ 0.4, 3 ~ 6)
   Diaphragm stroke mm (in) 3.5 ~ 5.1 (0.14 ~ 0.20)
    Plunger stroke mm (in) 5.85 ~ 9.05 (0.23 ~ 0.35)
OIL PUMP
    Type Trochoid
    Outer rotor-to-housing clearance (a) mm (in) 0.03 ~ 0.15 (0.001 ~ 0.006)
    Outer rotor-to-inner rotor clearance (b) mm (in) 0.12 max. (0.005 max.)
    Rotor-to-cover clearance (c) mm (in) 0.03 ~ 0.08 (0.001 ~ 0.003)
    Shaft-to-housing clearance (d) mm (in) 0.006 ~ 0.034 (0.0002 ~ 0.0013)
    Relief valve operating pressure MPa (kg/cm2, psi) 4.12 ±0.30 (0.0412 ±0.003,0.5859 ± 0.043)
CARBURETOR
    ID mark 65W00
    Main jet # 110
    Pilot jet # 50
    Pilot outlet jet # 52
    Float height mm (in) 10.0 ±0.5 (0.39 ±0.02)
    Float height r/min 925 ±25
    Float height r/min 820 ±25

Lower

Item-Worldwide/USA/Canada Unit Model
F20A   F25A
-   F25W
-   F25W
GEAR BACKLASH
    Pinion - forward mm (in) 0.31 - 0.72 (0.012 - 0.028)
    Mid-point mm (in) 0.51 (0.020)
    Pinion - reverse mm (in) 0.93 - 1.65 (0.037 - 0.065)
    Mid-point mm (in) 1.29 (0.051)
    Pinion shim mm 1.0, 1.1, 1.2, 1.3, 1.4, 1.5, 1.6
    Forward shim mm 1.0, 1.1, 1.2, 1.3, 1.4
    Reverse shim mm 1.0, 1.1, 1.2, 1.3

ELECTRICAL

Item Worldwide-USA-CANADA Unit Model Model
F20A  F25A
-  F25W
-  F25W
IGNITION SYSTEM
  Ignition timing Degree (BTDC) 10 -30 ±3
  Charge coil output peak voltage (G/W - W/G)
    @ cranking 1 V 210
    @ cranking 2 V 240
    @ 1,500 r/min V 210
    @ 3,500 r/min V 210
  Pulser coil output peak voltage (R - W)
    @ cranking 1 V 90
    @ cranking 2 V 90
    @ 1,500 r/min V 210
    @ 3,500 r/min V 240
  CDI unit output peak voltage (B/W - 0)
    @ cranking 1 V 180
    @ cranking 2 V 200
    @ 1,500 r/min V 190
    @ 3,500 r/min V 190
  Spark plug gap mm (in) 0.9 (0.04)
  Charge coil resistance (W/G - G/W) Ω 660-710
  Pulser coil resistance (R - W) Ω 300-350
  Ignition coil resistance
  Charge coil resistance (W/G - G/W) Ω 660-710
    Primary Ω 0.08 - 0.70
    Secondary kΩ 3.5 - 4.7
Item Worldwide-USA-CANADA Unit Model Model
F20A  F25A
-  F25W
-  F25W
IGNITION CONTROL SYSTEM
  Oil pressure switch kPa (kg/cm2, psi) 15.5 (0.16, 2.25)
  Power bobbin (Y/B - Y/B)loaded
    @ cranking 1 V 7
    @ 1,500 r/min V 30
    @ 3,500 r/min V 80
  open circuit
    @ cranking 2 V 10
    @ 1,500 r/min V 40
    @ 3,500 r/min V 80
  Electrothermal valve coil (Y/B - Y/B) Ω 6.7 ~ 7.1
  Engine temperature sensor resistance
    @ 5 °C (41 °F) kΩ 2.5
    @ 20 °C (68 °F) kΩ 1.25
    @ 70 °C (158 °F) kΩ 0.176
  Engine speed limiter
    Retard timing r/min 6,200
    Ignition off r/min 6,800
    Reset r/min 6,000
  Overheat speed control r/min 2,000
STARTING SYSTEM
    Fuse A 20
STARTING MOTOR
    Type Bendix
    Rating Second 30
    Output kW 1.1
    Brush length limit mm (in) 6.4 (0.25)
    Commutator undercut mm (in) 0.8 (0.03)
CHARGING SYSTEM
  Lighting coil output peak voltage (Y-Y)
  loaded
    @ cranking 1 V 10
    @ 1,500 r/min V 25
    @ 3,500 r/min V 65
  open circuit
    @ cranking 2 V 10
    @ 1,500 r/min V 25
    @ 3,500 r/min V 60
  Lighting coil resistance (Y - Y) Ω 0.22 ~ 0.24
  Rectifier/regulator output peak voltage
  loaded
    @ cranking 1 V 12
    @ 1,500 r/min V 12
    @ 3,500 r/min V 12
  open circuit
    @ cranking 2 V 9
    @ 1,500 r/min V 35
    @ 3,500 r/min V 15
  Charging current A @ 5,000 r/min 15(6)
  Lighting coil resistance (Y - Y) Ω 20 °C (68 °F) 0.9 - 1.1
ENRICHMENT CONTROL SYSTEM
  Electrothermal valve heater resistance Ω 20 °C (68 °F) 4
  Electrothermal ram projection (5 minutes powered) mm (in) 7 (0.3)
POWER TRIM AND TILT (PTT)
  Fluid type ATF, Dexron II
  Brush
    Length mm (in) 6 (0.25)
    Wear limit mm (in) 3 (0.12)
  Commutator
    Diameter mm (in) 16.5 (0.65)
    Wear limit mm (in) 15.5 (0.61)

DIMENSIONS

Outboard dimension

Bracket dimension

Share on social:

Productos relacionados