¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual Evinrude E-TEC G2 66°V6 2.7 L - Service Manual, P-N 5010056 Engine And Control Systems [Engine Management Module (Emm)]

Productos relacionados:
Service Manual Evinrude E-TEC G2 66°V6 2.7 L - Service Manual, P-N 5010056 Engine And Control Systems [Engine Management Module (Emm)]
5010056
BRP Marine

Engine Management Module (EMM)

The Engine Management Module (EMM) is a water-cooled controller. It controls engine management and engine–related remote control functions.

This section discusses the functions of the EMM and its various internal and external sensors. It also describes using Evinrude Diagnostics soft ware to retrieve and adjust service information saved in the EMM.

EMM Functions

The EMM controls the following processes and functions:

  • Alternator output; 55 V and 12 V

  • Start Assist Circuit (SAC) voltage boost

  • Fuel and ignition timing and duration

  • Fuel injector activation

  • Oil pump activation

  • Electric fuel lift pump control

  • Electric high pressure fuel pump control

  • Idle speed control

  • RPM limiter

  • Electrical circuit monitoring

  • Fault code creation and storage

  • Warning system activation

  • ROM verification, self-test

  • Cold starting

  • Output of diagnostic data

  • Tachometer signal

  • RPM profile and engine hours

  • Oil pump activation

  • Anti-knock compensation

  • Electronic throttle control

  • Electronic shift control

  • Dynamic Power Steering

EMM Connections

IMPORTANT: EMM connections and wiring must be clean and tight. Improper electrical connections can damage the EMM. DO NOT run the outboard with loose or disconnected wiring.

Make sure EMM connections are clean and tight.

  • Engine wire harness to EMM connectors; J1-A, J1-B, J2, J3, J4.

  • Stator to EMM connections; one 6-pin AMP and J2 connector.

  1. J1-A connector
  2. J1-B connector
  3. J2 connector
  4. J3 connector
  5. J4 connector

EMM Inputs and Outputs Diagram

  1. EMM

  2. 12 VDC Battery

  3. Fuel Vapor Separator

  4. Electronic Throttle Body

  5. Shift Actuator

  6. Knock Sensor (2)

  7. Engine Temperature Sensor (2)

  8. Exhaust Temperature Sender

  9. Trim Sender

10.Engine Oil Level Sender

11.Low Oil Switch

12.Digital Remote Control

13.Intake Air Temperature Sensor

14.Crankshaft Position Sensor

15.Trim Switch

16.Stator

17.DPS Pressure Sensors

18.Water in Fuel Sensor

19.Fuel Injector (6)

20.Ignition Coil (6)

21.Vapor Vent Solenoid

22.Digital Displays & Gauges

23.Oil Pumps

24.Dynamic Power Steering Module

25.Trim & Tilt Relay

26.Starter Solenoid & Motor

Share on social:

Productos relacionados