SPECIFICATIONS
- These specifications are subject to change without notice.
| Data | Data | Data | ||
|---|---|---|---|---|
| Item | Unit | DF60T | DF70T/WT | DF70WTH |
| PRE-FIX | 06001F | 07001F |
DIMENSIONS & WEIGHT

PERFORMANCE

POWERHEAD

| Data | Data | Data | ||
|---|---|---|---|---|
| Item | Unit | DF60T | DF70T/WT | DF70WTH |
FUEL & OIL

BRACKET

LOWER UNIT

SERVICE DATA
- These service data are subject to change without notice
| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
POWERHEAD

- Figures shown are guidelines only, not absolute service limits.
| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
CYLINDER HEAD/CAMSHAFT

| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
VALVE/VALVE GUIDE

| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
CYLINDER/PISTON/PISTON RING

| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
CRANKSHAFT/CONROD

| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
LOWER UNIT
Design specification thickness for shim & washer

ELECTRICAL

| Data | Data | ||
|---|---|---|---|
| Item | Unit | DF60T | DF70T/70WT/70WTH |
STARTER MOTOR

PTT MOTOR

SELF-DIAGNOSTIC SYSTEM INDICATION
When the abnormality occurs in a signal from sensor, switch, etc., the “CHECK ENGINE” lamp on the monitor-tachometer flashes (lights intermittently) according to the each code pattern with buzzer sounding.

• If more than two items fail at once, the self-diagnostic indication appears according to priority order.
The indication repeats three times.
• On the tiller handle (TH) model, alerts is signaled by a sound from the caution buzzer contained in the tiller handle.
TIGHTENING TORQUE
Tightening Torque – Important Fasteners
| ITEM | THREAD DIAMETER | TIGHTENING TORQUE | TIGHTENING TORQUE | TIGHTENING TORQUE | |
|---|---|---|---|---|---|
| N·m | kg-m | lb-ft | |||
| Cylinder head cover bolt | 6 mm | 10 | 1.0 | 7.0 | |
| Cylinder head bolt | 10 mm | 73 | 7.3 | 53.0 | |
| Crankcase bolt | 8 mm | 25 | 2.5 | 18.0 | |
| Crankcase bolt | 10 mm | 46 | 4.6 | 33.5 | |
| Conrod cap bolt | 8 mm | 35 | 3.5 | 25.5 | |
| Oil pump stopper | - | 50 | 5.0 | 36.0 | |
| Intake manifold bolt/nut | 8 mm | 23 | 2.3 | 16.5 | |
| Exhaust manifold bolt/nut | 8 mm | 23 | 2.3 | 16.5 | |
| Valve adjusting lock nut | 7 mm | 17 | 1.7 | 12.5 | |
| Rocker arm shaft screw | 6 mm | 11 | 1.1 | 8.0 | |
| Timing pulley nut | 38 mm | 70 | 7.0 | 50.5 | |
| Camshaft pulley bolt | 12 mm | 60 | 6.0 | 43.5 | |
| Oil pressure switch | - | 13 | 1.3 | 9.5 | |
| Oil regulator valve | 14 mm | 27 | 2.7 | 19.5 | |
| Delivery pipe bolt | 8 mm | 23 | 2.3 | 16.5 | |
| Delivery pipe plug/union bolt | Upper plug | 12 mm | 40 | 4.0 | 29.0 |
| Delivery pipe plug/union bolt | Lower union | 12 mm | 40 | 4.0 | 29.0 |
| Low pressure fuel pump bolt | 6 mm | 10 | 1.0 | 7.0 | |
| Thermostat cover bolt | 6 mm | 10 | 1.0 | 7.0 | |
| Water pressure valve cover bolt | 6 mm | 10 | 1.0 | 7.0 | |
| Flywheel bolt | 16 mm | 190 | 19.0 | 137.5 | |
| Starter motor mounting bolt | 8 mm | 23 | 2.3 | 16.5 | |
| Engine oil filter | - | 14 | 1.4 | 10.0 | |
| Engine oil drain plug | 12 mm | 13 | 1.3 | 9.5 | |
| Power unit mounting bolt/nut | 8 mm | 23 | 2.3 | 16.5 | |
| Power unit mounting bolt/nut | 10 mm | 50 | 5.0 | 36.0 | |
| Driveshaft housing bolt | 10 mm | 50 | 5.0 | 36.0 | |
| Upper mount nut | 12 mm | 80 | 8.0 | 58.0 | |
| Upper mount cover bolt | 10 mm | 50 | 5.0 | 36.0 | |
| Lower mount nut | 12 mm | 80 | 8.0 | 58.0 | |
| Lower mount cover bolt | 10 mm | 50 | 5.0 | 36.0 | |
| Clamp bracket shaft nut | 22 mm | 43 | 4.3 | 31.0 | |
| Water pump case bolt | 8 mm | 17 | 1.7 | 12.5 | |
| Gearcase bolt | 10 mm | 55 | 5.5 | 40.0 | |
| Propeller shaft bearing housing bolt | 6 mm | 10 | 1.0 | 7.0 | |
| Pinion nut | 12 mm | 100 | 10.0 | 72.5 | |
| Propeller nut | 18 mm | 55 | 5.5 | 40.0 | |
| Tiller handle pivot nut | 10 mm | 45 | 4.5 | 32.5 | |
| Tiller handle pivot bolt | 10 mm | 25 | 2.5 | 18.0 | |
| Tiller handle mounting lock nut | 10 mm | 50 | 5.0 | 36.0 | |
| Tiller handle mounting stud bolt | 10 mm | 25 | 2.5 | 18.0 |
ENGINE SERIAL NUMBER
The engine serial number starts from the following six-figure number located after the model pre-fix.

