¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual DF40, DF50 Troubleshooting [238][Df40, Df50]

Productos relacionados:
Service Manual DF40, DF50 Troubleshooting [238][Df40, Df50]
99500-87J08-01E
Suzuki Marine

TROUBLESHOOTING

Before starting troubleshooting, read and follow the “PRECAUTION ON SYSTEM INSPECTION” section on page 13-33.

In this section, troubleshooting procedures are based on the assumption that “low pressure fuel system” and “mechanical components (power unit, lower unit, etc.)” are normal.

For troubleshooting of “Starter motor will not run”, see page 4-7 in Service Manual P/N. 99500-87J0(cid:127)-01E.

CHART1 : SELF-DIAGNOSTIC CODE “3-4”

START

CHART2 : SELF-DIAGNOSTIC CODE “4-2”

START

• It will be possible to start engine if CKP sensor has failed.

CHART3 : SELF-DIAGNOSTIC CODE “3-1”

START

CHART4 : SELF-DIAGNOSTIC CODE “2-4”

START

It will be possible to start engine if CMP sensor has failed.

CHART5 : SELF-DIAGNOSTIC CODE “2-2”

START

In this case, CTP switch will be in “always ON” condition. (“24” terminal voltage will be 0V always regardless throttle position.)

CHART6 : SELF-DIAGNOSTIC CODE “1-4”

START

CHART 7 : SELF-DIAGNOSTIC CODE “2-3”

START

CHART8 : SELF-DIAGNOSTIC CODE “3-2”

START

CHART9 : SELF-DIAGNOSTIC CODE “1-1”

START

This self-diagnostic code indication may be canceled by turning ignition switch ON because ECM detects battery voltage.

It is difficult to check rectifier & regulator completely. Before replacing with new one, check if its ground point has good electrical contact.

CHART10 : SELF-DIAGNOSTIC CODE “1-5”

START

CHART11 : SELF-DIAGNOSTIC CODE “4-3"

START

CHART12 : ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)

START

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.
• Emergency stop switch plate is set in place.

CHART13 : UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)

Before starting this troubleshooting, make sure that :
• There is no self-diagnostic code indication.

START

If neutral switch has failed (while engine running), engine will tend to stall when shifting into gear. If neutral switch has failed as “always ON”, engine speed is limited to 3000 r/min by intermittent fuel injection and ignition timing is fixed at BTDC9 °. If neutral switch has faild as “always OFF”, engine cannot be cranked>

If CTP switch has failed, engine will tend to stall when decelerating.

: The self-diagnostic code “3-1” may not be indicated because IAC valve condition depends on ECM control. (See page 13-28.) If IAC valve has failed, “Fast-idle function (warm-up mode)” won’t operate.

Share on social:

Productos relacionados