¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual DF40, DF50 Idle Air Control System [58][Df40, Df50]

Productos relacionados:
Service Manual DF40, DF50 Idle Air Control System [58][Df40, Df50]
99500-87J08-01E
Suzuki Marine

BY-PASS AIR SCREW / PASSAGE

Since the throttle valve is almost fully closed when idling/ trolling, the main flow of air necessary to maintain idling / trolling speed passes through the by-pass air passage. The by-pass air adjustment screw controls the flow of air through the passage and provides a means of partially adjusting the total amount of air necessary for idling / trolling.

See page 2-14 for the by-pass air screw adjustment procedure.

IAC VALVE / PASSAGE

The IAC valve is a solenoid plunger type mounted on the electrical parts holder. Its purpose is to control the amount of intake air flowing from the IAC passage. The IAC valve is driven by the duty cycle signal from the ECM.

OUTLINE

The ECM controls the duty cycle signal of the IAC valve to regulate a portion of the intake air flow to the intake manifold.

This system is used for the following purposes:

• To keep idling / trolling at the specified speed.

• To improve drive ability when decelerating.
(Dash-pot effect)

•To improve engine starting and warm-up performance.
(Fast-idle function)

The sensors / switch shown below monitor current engine condition and send signals to the ECM. Based on these signals, the ECM determines the optimum duty cycle (repeating “ON” time rate within a cycle). A repeating ON/OFF signal at a specified rate (10 times a second) is then sent to the IAC valve.

CONTROL MODE

BEFORE START:

The IAC valve is always closed when engine is not running. (0% duty)

WHEN CRANKING :

The IAC valve is controlled to operate at 100% duty.

AFTER START ( FAST-IDLE FUNCTION ) :

The IAC valve is controlled to operate at 100% duty until the timer, which was set according to cylinder temperature at cranking, expires.

WHEN IDLING / TROLLING :

The IAC valve is controlled so that the engine speed is stable at the idling / trolling speed specified.
During this period, the IAC valve has a duty cycle of approx. 20% but will vary slightly as idling / trolling conditions change.

WHEN RUNNING ( NORMAL OPERATION ) :

The IAC valve is controlled to operate at 20 – 100% duty, which depends on the current engine conditions.

WHEN DECELERATING ( DASH-POT EFFECT):

When the throttle valve is suddenly returned to full close and the CTP switch signal changes to “ON”, the IAC valve operates at a controlled gradual return to idle / troll operating duty to prevent engine stalling or unstable running.

Due to the limited intake air flow from the IAC passage and in order to effectively use both the “Dash-pot effect” and “Fast-idle function”, the by-pass air screw must be adjusted to provide IAC valve operation at 20 ± 5% duty at the engine idling / trolling specification. See page 2-14 for the by-pass air screw adjustment procedure.

Share on social:

Productos relacionados