¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 5009001_15-30 HP - AA-AE Service Chart [Powerhead Disassembly]

Productos relacionados:
Service Manual 5009001_15-30 HP - AA-AE Service Chart [Powerhead Disassembly]
5009001
BRP Marine

POWERHEAD

Remove five inner exhaust housing screws and inner exhaust housing.

007743

  1. Screws

Remove three exhaust megaphone screws and exhaust megaphone.

007744

  1. Screws

POWERHEAD DISASSEMBLY

Systems Removal

To simplify reassembly and wiring installation, lay out the various screws and clamps in the order of their proper location.

Remove the oil tank. Refer to Oil Tank Assembly on p. 157.

Remove fuel pump assemblies, filter and fuel injectors. Refer to FUEL COMPONENT SERVICING on p. 130.

IMPORTANT: Mark injectors for cylinder location before removal. All injectors must be installed in their original location. Improper injector installation can result in powerhead failure.

Remove ignition coils.

Remove the electric starter. Refer to Starter Removal on p. 107.

Remove EMM and electrical harness assembly.
Refer to EMM SERVICING on p. 66.

Remove flywheel and stator. Refer to FLYWHEEL
AND STATOR SERVICING on p. 103.

Remove throttle linkage. Refer to Throttle Linkage Removal on p. 177.
Remove shift linkage. Refer to Shift Linkage Removal on p. 177.

Remove the throttle body and reed plate assemblies. Refer to Intake Manifold Service on p. 139.

Remove thermostat and pressure valve assembly.
Refer to THERMOSTAT AND PRESSURE RELIEF VALVE SERVICING on p. 168.

Remove oil supply and recirculation hoses.

Throttle Linkage Removal

Remove throttle cam and throttle lever.

007785

  1. Throttle cam
  2. Throttle lever

Shift Linkage Removal

Remove nut from shift lever. Remove shift lever and shaft assembly.


007745

1.Nut

Remove the ball, guide, and spring of the shift detent assembly from the crankcase.

007786

  1. Shift detent assembly

Cylinder Head Removal

Loosen in stages and remove cylinder head retaining screws. Remove the cylinder head. Discard cylinder head gasket.


007746

  1. Cylinder head screws (10 total)

Crankcase Disassembly
Remove screws and exhaust side water covers.

007747

IMPORTANT: Use care to avoid bending or damaging inner exhaust side cover.

007787
007788

Remove crankcase flange screws. Loosen in stages and remove the main bearing screws.

007748

  1. Flange screws
  2. Main bearing screws

Separate crankcase and cylinder block. It may be necessary to tap on crankshaft with a rawhide or rubber mallet to loosen.

007749

Crankshaft Assembly Removal

Carefully lift crankshaft straight up and remove from crankcase.

007750

Connecting Rods and Pistons

Use an appropriate ring expander to remove all piston rings from pistons. Discard the rings.

Wear safety glasses to avoid injury.

007751

007752

The wrist pin fit is loose on both sides. Push the wrist pin through to free the piston from the connecting rod. If necessary, use Wrist Pin Pressing Tool, P/N 326356, to remove the wrist pin.

007753

Crankshaft Service

Remove upper seal from crankshaft. Discard the seal. A new upper seal must be installed on assembly.

Remove the upper main bearing.

007754

  1. Upper oil seal
  2. Upper main bearing

Remove the lower bearing seal housing.

Remove the housing O-ring. Discard O-ring.

007789

Use a punch to remove the housing seal. Discard seal.


007790

1.Punch

Inspect housing and replace if necessary.

Remove the O-ring from crankshaft sleeve and inspect it. Replace the O-ring if it is not in good condition.

007791

Inspect the crankshaft sleeve and replace if necessary. To remove the sleeve, use Slide Hammer, P/N 432128, and Puller Jaws, P/N 432130.

007792

Remove the lower main bearing only if it needs to be replaced. Use external retaining ring pliers to remove the lower bearing retaining ring.

007756

IMPORTANT: If the lower main bearing is removed from the crankshaft, it must be discarded. DO NOT reuse it.

Use a bearing separator to support the bearing, and press off the crankshaft.

007793

Share on social:

Productos relacionados