¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 5008851_9.8 HP Introduction

Productos relacionados:
Service Manual 5008851_9.8 HP Introduction
5008851
BRP Marine

Introduction

Before reading this manual

This service manual provides information that is needed for inspection, service and repair of applicable outboard motors. For information about operation of the products that are not described in this document, refer to the owners manual. For our customers' safe and dependable use of the product for long term, it is essential to maintain the performance and quality of the outboard. To ensure this, the maintenance and service have to be done properly by service technicians with fundamental knowledge and skills. This manual is utilized so that our customers can always use their outboard motor with full satisfaction.

Safety Information

Safety Statements

The following safety statements are found throughout this manual and indicate information which, if ignored, could result in fatal safety hazards or property damage:

Indicates the presence of a hazard which, if ignored, will result in severe injury or death.

Indicates the presence of a hazard or an unsafe activity which, if ignored, could result in severe injury or death.

Indicates the presence of a hazard or an unsafe activity which, if ignored, could result in minor personal injury or damage to
the products or facilities.

Attention:

About this manual

This service manual is designed so that service persons are able to perform their work correctly. Understand the following matters well for efficient repairs.

(1) Each chapter begins with the introduction of special tools that are used for the work described in the chapter so that the service persons are able to understand the tools needed.

(2) Parts that are serviced in each chapter and their details are presented by using a component composition diagram.

(3) Fastening torques are described in the component composition diagram and in the body text and are critical points of the applicable repair.

(4) Pictograms indicate that there is an important instruction for the relevant parts. It also shows the type of lubricant and its application point(s).

(5) The component composition diagrams describe the names of the parts, the quantity of the parts used, size of fasteners and special notes.

(6) Specific works are described in detail by using illustrations and adding advice on the work.

This manual uses SI unit system (International System of Units) for pressure, force (load), torque and stress. This manual newly adopts the international unit construction system (SI unit system) followed by the conventional imperial and metric systems enclosed by ( ) and [ ] as described below.

  • Measurements are shown using SI unit followed by conventional units (US unit) and [Japanese domestic unit].

Example :

  • The conventional unit for measurement of force uses "kgf (kilogram force)" to discriminate it from "kg (mass kilogram)" of SI unit system.

Example :
900 cm3 (30.4 fl.oz)

Example :
10 mm (0.39 in)

What is the SI unit system? Although the measurement unit is standardized mostly with metric system in the world, the metric system includes different kinds of unit systems.

Though the metric system was established expecting that a single unit system would be used in the world, various physical units were established later, resulting in branching the metric system in different unit systems.

The new unit system is called "International System of Units" because it was established for the purpose of unifying the different unit systems.

Since the metric system was initially established in France, and International Bureau of Weights and Measures (IBWM) is located in Paris, General Conference of Weights and Measures (GCWM) passed a resolution of the international unit system as "Systéme International d'Unités (French)" that is abbreviated as "SI unit".

For example, conventional metric system uses the unit of mass (kg) and unit of force (kg or kgf) without discriminating them, but the SI unit system uses, for example, "kg" as the unit of mass, and "N" as the unit of force, aiming to apply a kind of unit for a kind of physical quantity.

Description of Pictograph

Share on social:

Productos relacionados