¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 5008736_55 MFE Engine Cover Service [Lower Cover Service]

Productos relacionados:
Service Manual 5008736_55 MFE Engine Cover Service [Lower Cover Service]
5008736
BRP Marine

Lower Cover Removal

Remove four carry handle screws and bushing caps. Remove carry handle and bushings.


005061

  1. Carry handle
  2. Screws

Remove nut and washer from dewater valves. Remove valves from cover.


007849

  1. Nut
  2. Washer

Remove lower engine cover screws, including one at inside, top rear.


007845

  1. Cover screws


002150

  1. Top, rear cover screw

Loosen port cove r slightly , and disconnect fuel selector switch connector. Then, remove port cover.


005063

  1. Fuel map switch connector

Tilt the starboard cove r to remove it below the grommet. Leave the grommet in place.

IMPORTANT: Cover and grommet installation is easiest if the grommet is in place first.

Lower Cover Installation

Installation of lower motor covers will be easiest if the following steps are performed in sequence:

  • Install air silencer on throttle body.

  • Secure grommet on cables with tie strap.

  • Slide starboard cover on t o grommet from the bottom and then into position on outboard.

  • Connect fuel map switch connector.

  • Place port side cover into position on outboard.


005063

  1. Fuel map switch connector

Start the screw above the exhaust relief grommet first. Tighten just enough to hold the grommet in place.


002157

  1. Start this screw first
  2. Exhaust relief grommet

Start the top front screw next an d draw cover halves together.


002165

  1. Start this screw second

Install remaining cover screws and tighten all screws to 24 to 36 in. lbs. (3 to 4 N·m).


007845

  1. Cover screws


002150

  1. Top, rear cover screw

Place de-water valves through holes. Align tab of de-water valve with alignment notch as shown.


008177

  1. Tab
  2. Alignment notch

Install washer and nut. Tighten to a torque of 25 to 40 in. lbs. (3 to 4.5 N·m). Lever should point to the rear of the outboard when the valve is closed.


007849

  1. Washer
  2. Nut

Install long bushings on front cover pins and short bushings on rear pins. Install carry handle. Secure with bushing caps and screws.


005061

  1. Carry handle
  2. Screws

Latch Handle Installation

Apply a light coat of Triple-Guard grease to latch handle shaft. Insert handle into lower cover.


006470

  1. Triple-Guard grease

Apply Ultra-Lock to screw thread s. Place spring washer and hook into position and tighten screw to a torque of 180 in. lbs. (20 N·m).


006471

  1. Spring washer
  2. Hook
  3. Screw

Fuel Selector Switch Installation

Place switch into position through cover.


007846

  1. Fuel selector switch

Install lock washer and nut on switch. Tighten nut to a torque of 10 to 16 in. lbs. (1 to 2 N·m).


007847

  1. Nut and washer

Install electrical connector. Refer to AMP Connectors on p. 128.


006472

De-Water Valve Service

Install drain valve hoses on reed plate and secure with tie straps.


005062

  1. Drain valve hoses

Install drain valve through cover with outlets pointed down.


007848

  1. Drain outlet

Install washer and nut. Tighten to a torque of 25 to 40 in. lbs. (3 to 4.5 N·m). Lever should point to the rear of the outboard when the valve is closed.


007849

  1. Washer
  2. Nut
Share on social:

Productos relacionados