¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 5008330_55 HP MFE Gearcase [Water Pump Service]

Productos relacionados:
Service Manual 5008330_55 HP MFE Gearcase [Water Pump Service]
5008330
BRP Marine

Disassembly

Remove the four impeller housing screws.

    1. Impeller housing screws

Slide the water pump off the driveshaft. Remove the impeller key, impeller plate, and gasket. Discard the gasket.

    1. Impeller plate
    1. Drive key

Remove all the parts from the housing.

Inspection

Check impeller for overheating, hub separation, and other wear or damage.

Check liner and wear plate for scoring, distortion, and impeller material transfer.

Inspect the housing for cracks or melting.

Make sure gasket surface is clean and smooth.

Assembly

Lightly coat the exterior rim of the impeller cup with Gasket Sealing Compound. Install the cup in the impeller housing. The cup locks in place in the housing with a square index tab.

    1. Index tab

IMPORTANT: Do not allow any sealer to get into the air bleed groove in the impeller housing. If this groove is blocked by adhesive, the pump will lose its prime and will not pump water.

    1. Air bleed groove

Lightly coat the inside of the liner with TripleGuard grease. With a counterclockwise rotation, install the impeller into the liner with the slot for the impeller key facing out.

Apply a thin bead of Adhesive 847 in the seal groove, and install the special shaped O-ring seal.

    1. Impeller
    1. O-ring seal

Apply Gasket Sealing Compound to both sides of
a new impeller plate gasket. Install the gasket and
impeller plate.

Apply Triple-Guard grease to temporarily hold impeller key in place.

    1. Impeller plate gasket
    1. Impeller plate
    1. Drive key

The sharp edge of the key is the leading edge in clockwise rotation.

Slide the water pump down the driveshaft. Align impeller slot with the impeller key. Rotate the driveshaft to engage the key with the impeller, and slide water pump down over key. Be sure impeller key does not fall out of position.

    1. Sharp edge of drive key
    1. Direction of driveshaft rotation

Make sure the impeller engages the impeller key. Serious powerhead damage will result if impeller key is not in place.

Align the impeller housing with the gearcase. Apply Gasket Sealing Compound to threads of the four impeller housing screws. Install the screws and tighten to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

Install the water tube grommet on the impeller housing.

Apply a thin bead of Adhesive 847 to groove of the impeller housing grommet. Install the grommet on the impeller housing.

    1. Housing screws
    1. Water tube grommet
    1. Impeller housing grommet

Before installing gearcase, shift rod adjustment MUST be checked. Refer to SHIFT ROD ADJUSTMENT on p. 244.

Share on social:

Productos relacionados