¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 25-30 HP E-TEC Gearcase [Bearing And Seal Removal]

Productos relacionados:
Service Manual 25-30 HP E-TEC Gearcase [Bearing And Seal Removal]
5007802
BRP Marine

Step 1: BEARING AND SEAL REMOVAL

IMPORTANT: Inspect bearings for damage while in place. If bearing is damaged, remove and discard. If the bearing is removed for any reason, it must be replaced

Step 2: Driveshaft Seals

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove the two driveshaft seals. Discard the seals.

Step 3: Driveshaft Bearing

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131 to remove the driveshaft bearing and sleeve from the gearcase. Discard the bearing.

Step 4: Pinion Bearings

Assemble the following components from Universal Pinion Bearing Remover and Installer, P/N 5005927.

  1. Rod, P/N 326582
  2. Pilot Plate, P/N 326583
  3. Remover and Installer, P/N 326577
  4. 1/4-20 x 1/2 in. hex head screw
  5. 1/4-20 x 11/4 in. hex head screw
  6. 1 in. O.D. flat washer

Place the tool in gearcase. using a mallet, drive the pinion bearings into the gearcase propeller shaft cavity. Discard the bearings.

Step 5: Forward Bearing

Use Slide Hammer, P/N 432128, and Bearing Puller, P/N 432130, to remove the forward bearing cup from the gearcase.

Secure the puller jaws into grooves behind the cup. Use Wrench, P/N 334359, to hold the puller while tightening the jaws.

  1. Bearing puller
  2. Wrench

Step 6: Shift Rod Bushing and O-ring

Position Shift Rod Bushing Remover, P/N 327693, under the shift rod bushing.

Thread the adapter of the Slide Hammer, P/N 391008, in the slide hammer. Place the adapter through the shift rod bushing and thread into the remover tool.

Remove the handle from the remover tool. Then remove the bushing from the gearcase.

Once the bushing has been removed from the gearcase, examine the bushing for damage. If damaged, replace the bushing on reassembly. Remove and discard the O-ring(s) and washer from the bushing.

  1. Adapter
  2. Shift rod bushing
  3. Remover tool, P/N 327693

Step 7: Prop Shaft Bearing Housing Seals and O-ring

Remove and discard the propeller shaft bearing housing O-ring.

  1. O-ring

Use Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove seals. Discard seals.

  1. Small puller jaws

Useg Puller Bridge, P/N 432127, and Small Puller Jaws, P/N 432131, to remove both propellers shaft bearings from the bearing housing. Discard both bearings.

  1. Small puller
Share on social:

Productos relacionados