¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Service Manual 115-200 HP 60° V4-V6 E-TEC Gearcase [Gearcase Disassembly (Counter)]

Productos relacionados:
Service Manual 115-200 HP 60° V4-V6 E-TEC Gearcase [Gearcase Disassembly (Counter)]
5007529
BRP Marine

GEAR CASE DISASSEMBLY

IMPORTANT: Counter rotation (CR) gearcases use unique components and require different service procedures. Use care when working on counter rotation gear cases. DO NOT interchange parts between standard and counter rotation models. Identify gear case type before disassembly. Make sure the “CR” marking is on the end of the propeller shaft.

Pre-Disassembly Inspection

Refer to Pre-Disassembly Inspection on p. 307.

Propeller Shaft Bearing Housing Removal – “O” and “M” Type

Remove the two screws, washers, and retainers holding the propeller shaft bearing housing.

  1. “CR” marking
  2. Retainer tab screws

Remove wedge, screw, and washer.

To remove the propeller shaft, bearing housing and forward gear from gearcase, thread Propeller Shaft Adapter, P/N 432398, onto Slide Hammer, P/N 432128, until it seats. Thread adapter completely onto propeller shaft and pull propeller shaft, bearing housing, and forward gear assembly out of gearcase.

  1. Adapter, P/N 432398

Propeller Shaft Bearing Housing Removal – “M2” Type

IMPORTANT: The propeller shaft bearing housing on “M2” type gearcases is PRESSED into gearcase housing.

Remove the two retaining screws holding the propeller shaft bearing housing.

  1. “CR” marking
  2. Retainer screws

Remove the propeller shaft bearing housing from the gearcase using:
• Propeller Shaft Bearing Housing Puller Kit, P/N 354060.

DO NOT use tools designed to push on the propeller shaft. Pushing against the propeller shaft could damage the forward gear thrust bearing or thrust washer.

Install the threaded adaptor from the puller kit on to the propeller shaft until seated.

Assemble puller kit components. Hold adaptor with wrench and turn nut clockwise to pull bearing housing.

Pull propeller shaft and bearing housing far enough to loosen the PRESSED bearing housing from the gearcase housing.

“M2” Type Gearcase

Remove propeller shaft, forward gear and bearing housing assembly from gearcase.

Pinion Gear Removal and Driveshaft Servicing

Refer to Pinion Gear and Driveshaft Removal – “O”, “L”, “L2”, “M” and “M2” Type on p. 313.

Shift Housing, Gear and Propeller Shaft Removal

Push down on the shift rod. This will move the detent lever downward to clear the inside of the gearcase when the shaft assembly is pulled out. Unscrew the shift rod from the detent lever. Remove screws, cover, and shift rod from the gearcase.

Discard the cover gasket. Remove the shift rod O ring from inside of cover and discard.

  1. Cover gasket

Use an appropriate tool to apply downward pres sure on the detent while pulling on the propeller shaft assembly. Remove propeller shaft assembly from the gearcase.

Counter Rotation Models

  1. Tool

Water Intake Screens

Remove and clean water intake screens. Replace if damaged.

  1. Water intake screen

GEARCASE HOUSING INSPECTION

Refer to GEARCASE HOUSING INSPECTION on p. 316.

Share on social:

Productos relacionados