Remote Control Conversion Kit 1

Duración de la reparación: 30 to 60 mins

Dificultad de la reparación: Easy

added February 18, 2019 at 10:15 PM updated May 16, 2019 at 8:34 PM

Remote Control Conversion Kit 1

BRP Marine Outboard

Sections:

Preface
Install Control Cables

SAFETY

These installation instructions contain information that can help prevent personal injury and damage to equipment. Understand the following symbols before proceeding:

Alerts you to the possibility of danger and identifies information that will help prevent injuries.

Identifies information that will help prevent damage to machinery.

Appears next to information that controls correct assembly and operation of the product.

TO THE OWNER

The assembly procedures outlined in this sheet should be performed by a skilled technician. If you have questions, see your DEALER. Save these instructions in your owner's kit. This sheet contains information important to the future use and maintenance of your engine.

TO THE INSTALLER

Give this sheet to the owner. Advise the owner of any special operation or maintenance information contained in the instructions.

Preface

PREFACE

This kit converts 1993 (ET) and newer 9.9/15 model Evinrude® and Johnson® outboard motors to remote shift and throttle operation.

[1]
Contents of Kit

Ref.	Name of Part	Qty.
1	Shift Link	1
2	Shift Lever	1
3	Shift Lever Screw	1
4	Bushing	1
5	Tie Strap	2
6	Grommet	1
7	Clevis Pin	2
8	Cotter Pin	2
9	Anchor Pocket Cover	2
10	Cover Screw	2

Remove stop switch clip to prevent accidental starting.

[2]
Remove screws (A) and lower motor covers.

[3]
Remove throttle cable anchor screw and washer (B) from powerhead. Install screw and washer in hole (C) to save parts for future reconversion to tiller control.

[4]
Pry out throttle cable pin (D), remove cable. Reinstall pin in connector (E).

[5]
Remove throttle lever screw and washer (F). Washer will be reused.

[6]
Rotate propeller and shift motor into FORWARD gear.

[7]
Insert shift link (1) into detent lever (A), and rotate link back. Shift motor into NEUTRAL.

[8]
Assemble shift lever (2) on shift link (1). Insert shift lever screw (3) thru washer saved (B) and bushing (4).

[9]
Coat bushing (4) with Triple-Guard® 0508298 grease and push bushing into shift lever (2). Insert screw through bushing in throttle lever (C), and into block. Tighten screw to 60-84 in. lbs. (7-9 Nm).

[10]
Pull tiller handle throttle cable (D) out from under starter handle to the port side of motor.

[11]
Route cable back along bottom of lower motor cover, up outside the starter (E), and forward to the manual starter mounting post (F). Secure to post with a tie strap (5).

Install Control Cables

[12]
Remove starboard grommet (G) and save for future reconversion to tiller control. Using a knife, carefully cut out choke shaft hole (H) in grommet (6) included.

[13]
Cut a slit (I) in grommet (6) to the choke shaft hole.

[14]
Extend control cables and lubricate casings with Triple-Guard® grease. Install shift cable (A) and throttle cable (B), securing the casing guides (C) with clevis pins (7) and cotter pins (8).

Secure clevis pins by spreading cotter pin ends.

[14]
Secure cable trunnions (D) with anchor pocket covers (9) and cover screws (10). See the Service Manual, Section 9 - Throttle and Shift Cable Installation for procedures.

[15]
Replace lower motor covers. Install control cables in grommet (6).

After cables are installed, verify that the controls work as intended for safe operation.

Check idle speed. See Service Manual, Section 1 - Synchronization and Linkage Adjustments for procedures.

5007742 - Remote Control Adapter
0176494 - Remote Control Adaptor Kit

Share on social: