¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Power Unit [Recoil Starter] [2002]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Power Unit [Recoil Starter] [2002]
LIT-18616-01-65
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
RECOIL STARTER REMOVAL Follow the left "Step" for removal.
1 Start-in-gear protection wire 1 - for start-in-gear protection model
2 Bolt (with washer) 3 6 x 20 mm
3 Collar 3
4 Recoil starter assembly 1
Step Procedure/Part name Q'ty Service points
RECOIL STARTER DISASSEMBLY
1 Cotter pin 1 for start-in-gear protection model
2 Plane washer 1
3 Reel stopper 1
4 Stopper arm 1
5 Spring 1
6 Screw 1
7 Cover 1
8 Starter handle 1
9 Starter rope 1
10 Bolt (with washer) 1
11 Drive plate 1
12 Drive pawl spring 1
13 Sheave drum assembly 1 NOTE:
Position the inner end of the spiral spring on the retainer post of the sheave drum.
Wind up the spring 2-1/2 turns counter clockwise with the starter rope.
14 Bushing 1
15 Spiral spring 1
16 Starter case 1
Step Procedure/Part name Q'ty Service points
SHEAVE DRUM DISASSEMBLY
17 Circlip 1
18 Drive pawl 1
19 Spring 1
20 Return spring 1
21 Rope guide 1
22 Starter rope 1 NOTE:
Wind the rope 2 turns around the sheave. drum.
23 Sheave drum 1
Reverse the removal steps for installation.

SERVICE POINTS

Sheave drum removal

1.Turn:

  • Sheave drum (1)
    Turn the sheave drum clockwise until the spiral spring is free.

NOTE:

  • Turn the sheave drum so that the cutaway on the outer surface of the sheave drum faces toward the starter handle.
  • Pass the starter rope through the cut.

  1. Remove:
  • Sheave drum

WARNING:
When removing the sheave drum, be sure to turn the sheave drum upside down to prevent the spiral spring from popping up at you.

Spiral spring removal

  1. Remove:
  • Spiral spring (1)

WARNING:
Be careful so that the spiral spring does not pop out when removing it. Remove it by allowing it out one turn of the winding each time.

Starter stopping plunger inspection

  1. Inspect:
  • Starter stopping plunger
    Crack/Wear/Damage -> Replace

Drive pawl and spring inspection

  1. Inspect:
  • Drive pawl
    Crack/Wear/Damage -> Replace.
  • Drive pawl spring
    Broken/Bent/Damage -> Replace.

Bushing inspection

  1. Inspect:
  • Bushing
    Crack/Damage -> Replace.

Sheave drum inspection

  1. Inspect:
  • Sheave drum
    Crack/Damage -> Replace.

Spiral spring inspection

  1. Inspect:
  • Spiral spring
    Broken/Bent/Damage ->Replace.

Starter rope inspection

  1. Inspect:
  • Starter rope
    Fray/Wear/Damage -»Replace.

NOTE:
When replacing the rope, cut it to the specified length and burn the rope end so that it will not travel.

Starter rope length: 1,800 mm (70.9 in)

Recoil starter checking

  1. Check:
  • Starter operation
    Rough operation —> Repair.
Share on social:

Productos relacionados