¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Power Unit [Power Unit Removal And Installation] [2002]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1996 - 2002 5hp All
Yamaha Outboard 1996 - 1999 4hp All

Power Unit [Power Unit Removal And Installation] [2002]
LIT-18616-01-33
Yamaha Marine

PREPARATION FOR REMOVAL

  • Remove the top cowling.
  • Remove the fuel tank and hose. Refer to the “FUEL SYSTEM” section in CHAPTER 4.
  • Remove the carburetor.
    Refer to the “FUEL SYSTEM” section in CHAPTER 4.

NOTE ON REMOVAL AND REASSEMBLY

Extent of removal: (1) Power unit removal

  • Clean all dirt, mud, dust and foreign material from the engine before the engine is removed and disassembled.
  • To ensure that you can perform the work cleanly and efficiently, check that you have the proper tools and cleaning equipment before commencing engine removal and reassembly.

REMOVAL POINTS

Start-in-gear protection wire (For start-in-gear protection model)

  1. Remove:
    • Clip (1)
    • Link (2)

Stop switch/Engine stop switch lead

  1. Remove:
    • Black (B) lead (1) (ground lead)
  2. Disconnect:
    • White (W) lead (2)
  3. Remove:
    • Stop switch (3)

Ignition coil bracket

  1. Remove:
    • Bolt (1)
    • Spark plug cap (2)
    • Ignition coil bracket (3)

ASSEMBLY AND INSTALLATION

Always use new gaskets, oil seals and O-rings. The use of any used oil seal or O-ring may result in oil leakage due to invisible scratches or stretches.
Apply grease to parts where specified.

Power unit

  1. Apply:
    • Gasket Maker
      Onto both faces of the gasket.

Clean the contacting surfaces of crankcase and bottom cowling.

  1. Install:
    • Dowel pin (1)
    • Gasket (2) (new)

  1. Install:
    • Power unit (1)

Insert the drive shaft into the crankshaft. If the splines will not come in complete mesh, rotate the crankshaft a little so that they are in mesh correctly.

  1. Install:
    • Mount bolt (1)
    • Mount bolt (2)

Tighten the bolts in two steps of torque.

Mount bolt:
1st : 3 Nm (0.3 kg•m, 2.2 ft•lb)
2nd : 8 Nm (0.8 kg•m, 5.8 ft•lb)

  1. Install:
    • Stop switch/Engine stop switch (1)
    • White lead (2)
    • Black lead (3)
  1. Install:
    • Link (1)
    • Clip (2)
  1. Adjust:
    • Throttle wire
      Refer to the “PERIODIC SERVICE" section in CHAPTER 3.
  1. Adjust:
    • Idle speed
      Refer to the “PERIODIC SERVICE” section in CHAPTER 3.
Share on social:

Productos relacionados