¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Owner's Manual DF25A, DF30A Operation[Stopping The Engine]

Productos relacionados:
Owner's Manual DF25A, DF30A Operation[Stopping The Engine]
99011-94L40-03B
Suzuki Marine

REMOTE CONTROL MODEL Shifting

To shift into “FORWARD”, squeeze the lock-out lever on the control handle and move the control handle forward to approximate position (A), as shown in the illustration.

To shift into “REVERSE”, squeeze the lock-out lever on the control handle and move the control handle rearward to approximate position (B), as shown in the illustration.

A detent or notch is present on all Suzuki control boxes to provide a “feel” for positions (A), (B), and neutral. Always shift quickly and firmly from neutral to position (A) or (B) to prevent abnormal wear on the gear and clutch engagement sur faces.

Speed control

To increase speed after you have shifted into gear, continue moving the control handle for ward or rearward.

Since the same handle is used for shifting and speed control it is possible to move the handle past the detent and engage the throttle. This can cause the boat to move suddenly resulting in personal injury or property damage. You must be careful not to move the control handle too far forward or rearward when shifting.

STOPPING THE ENGINE

When it is necessary to stop the engine in an emergency, pull the emergency stop switch lock plate out of the emergency stop switch by pulling the emergency stop switch cord.

TILLER HANDLE MODEL

  1. Turn the throttle control grip to the idle position.

  2. Shift into “NEUTRAL”.

  3. After operating at full throttle, cool off the engine a few minutes by allowing it to idle or troll at low speed.

  4. Push and hold in the stop button A until the engine stops.

  1. After stopping the engine, disconnect the fuel connector from outboard motor.

If you leave the motor stopped for a long period of time with the fuel line connected, fuel can leak out. Disconnect the fuel line, whenever you leave the motor stopped for a long period of time.

  1. Turn the air-vent screw on the fuel tank cap clockwise to shut the vent.

REMOTE CONTROL MODEL

To stop the engine:

  1. Shift into “NEUTRAL”.

  2. After operating at full throttle, cool off the engine a few minutes by allowing it to idle or troll at low speed.

  3. Turn the ignition key to the “OFF” position. Always leave the ignition key in the “OFF” position when the motor is not running, or battery can discharge.

  1. After stopping the engine, disconnect the fuel connector from outboard motor.

If you leave the motor stopped for a long period of time with the fuel line connected, fuel can leak out. Disconnect the fuel line, whenever you leave the motor stopped for a long period of time.

  1. Turn the air-vent screw on the fuel tank cap clockwise to shut the vent.

Unauthorized use of your boat could lead to an accident or damage to your boat. To prevent unauthorized use of your boat, be sure to remove the key and emergency stop switch lock plate when the boat is unattended.

To make sure that the emergency stop switch operates properly, stop the engine occasionally by pulling out the lock plate, while operating the engine at idling speed.

Share on social:

Productos relacionados