¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Lower Unit [Propeller Shaft And Reverse Gear] [2002]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Lower Unit [Propeller Shaft And Reverse Gear] [2002]
LIT-18616-01-65
Yamaha Marine

Step 1: EXPLODED DIAGRAM

Step 2: REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
PROPELLER SHAFT AND REVERSE GEAR REMOVAL Follow the left "Step" for removal.
Gear oil Refer to the "LOWER UNIT" section in chapter 3.
Propeller Refer to the "LOWER UNIT REMOVAL" section.
1 Bolt (with washer 2 6 x 20 mm
2 Propeller shaft housing assembly 1
3 Plate washer 1
4 Propeller shaft 1
5 Cross pin ring 1
6 Cross pin 1 NOTE : By pushing the shift plunger, bring the cross pin hole in the dog clutch with the hole in the shift slider.
7 Dog clutch 1 NOTE : Install the clutch with "F" mark toward the forward gear side.
8 Shift plunger 1
9 Spring 1
PROPELLER SHAFT HOUSING DISASSEMBLY
(1) O-ring 1
(2) O-ring 1
(3) Reverse gear 1
(4) Reverse gear shim *
(5) Ball bearing 1
(6) Oil-seal 2
(7) Needle housing 1
(8) Propeller Shaft housing 1
Reverse the removal steps for installation.

*: As required

Step 3: SERVICE POINTS

Propeller shaft housing removal

  1. Remove:
    • Propeller shaft housing assembly

Bearing housing puller :
  YB-06234..........(1)
  90890-06503 ......(3)
Universal puller :
  YB-06117..........(2)
Stopper guide plate :
  90890-06501 ......(4)
Center bolt :
  90890-06504.......(5)

[A] For USA and CANADA
[B] Except for USA and CANADA

Propeller shaft housing disassembly

  1. Remove:
    • Ball bearing (1)

Slide hammer set :
  YB-06096........(2)
Stopper guide plate :
  90890-06501.....(3)
Bearing puller :
  90890-06535.....(4)
Stopper guide stand :
  90890-06538.....(5)

[A] For USA and CANADA
[b] Except for USA and CANADA

  1. Remove:
    • Needle bearing

Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616

Reverse gear inspection

  1. Inspect:
    • Tooth
    • Dog
      Wear/Damage ➝ Replace

Bearing inspection

  1. Inspect:
    • Bearing
      Pitting/Rumbling ➝ Replace.

Propeller shaft housing inspection

  1. Clean:
    • Propeller shaft housing
      Use a soft brush and solvent
  2. Inspect:
    • Propeller shaft housing
      Crack/Damage ➝ Replace.

Dog clutch inspection

  1. Inspect:
    • Dog clutch
      Wear/Damage ➝ Replace.

Propeller shaft inspection

  1. Inspect:
    • Propeller shaft
      Wear/Damage ➝ Replace

Propeller shaft housing assembly

  1. Install:
    • Needle bearing

Depth (a) : 0 mm (0 in)

Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616

  1. Install:
    • Oil seal

Depth (a) : 3.0 ~ 3.5 mm (0.12 ~ 0.14 in)

Oil seal installer : YB-06168
Driver rod : YB-06071

  1. Install:
    • Ball bearing

Bearing installer : YB-06015
Driver rod : YB-06071

Share on social:

Productos relacionados