¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Lower Unit [Backlash (F50:F50A)] [2004]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 2004 60hp All
Yamaha Outboard 2004 60hp All

Lower Unit [Backlash (F50:F50A)] [2004]
LIT-18616-FT-60
Yamaha Marine

Backlash (F50/F50A)

Measuring the forward and reverse gear backlash

  1. Remove the water pump assembly.

  2. Set the gearshift to the nuetral position.

[A] For USA and Canada
[B] For worldwide

Shift rod push arm: YB-06052
Shift rod push arm: 90890-06052

  1. Install the special service tool so that it pushes against the propeller shaft.

[A] For USA and Canada
[B] For worldwide

NOTE:
Tighten the universal puller or center bolt while turning the drive shaft until the drive shaft can no longer be turned.

Bearing housing puller (1): YB-06234
Universal puller (2): YB-06117
Bearing housing puller claw (3): 90890-06564
Stopper guide plate (4): 90890-06501
Center bolt (5): 90890-06504

  1. Install the backlash indicator onto the drive shaft (18 mm [0.71 in] in diameter), then the dial gauge onto the lower unit.

NOTE:
Install the dial gauge so that the plunger (a) contacts the mark (b) on the backlash indicator.

Backlash indicator gauge (6): YB-06265
Backlash indicator (6): 90890-06706
Magnetic plate (7): YB-07003
Magnet base plate (7): 90890-07003
Dial gauge (8): YU-03097
Dial gauge set (8): 90890-01252
Magnet flexible stand (9): YU-34481
Magnet base (9): 90890-06705

  1. Slowly turn the drive shaft clockwise and counterclockwise and measure the backlash when the drive shaft stops in each direction.

Forward gear backlash: 0.18-0.54 mm (0.007-0.021 in)

  1. Add or remove shims if out of specification.
Forward gear blacklash Shim thickness
Less than 0.18mm (0.007)in) To be decreased by (0.36-M)x 0.56
More than 0.54 mm (0.021 in) To be increased by (M-0.36) x 0.56

M: Measurement

Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools from the propeller shaft.

  2. Apply a load to the reverse gear by installing the propeller (10) without the spacer (11), the washer (12) backwards, then the washer (13) as shown.


S62Y6470

NOTE:
Tighten the propeller nut (14) while turning the drive shaft until the drive shaft can no longer be turned.

  1. Slowly turn the drive shaft clockwise and counterclockwise and measuring the backlash when the drive shaft stops in each direction.


S62Y6475

Reverse gear backlash: 0.71-1.07 mm (0.028-0.042 in)

  1. Add or remove shims if out of specification.
Reverse gear backlash Shim thickness
Less than 0.71 mm (0.028 in) To be decreased by (0.89-M)x 0.56
More than 1.07 mm (0.042 in) To be increased by (M-0.89) x 0.56

M: Measurement

Available shim thicknesses: 0.10, 0.12, 0.15, 0.18, 0.30, 0.40, and 0.50 mm

  1. Remove the special service tools, and then install the water pump assembly.
Share on social:

Productos relacionados