¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Fuel System [Carburetor] [2008]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha International 2001 - 2005 4hp All
Yamaha Outboard 1999 - 2005 4hp All

Fuel System [Carburetor] [2008]
LIT-18616-01-79
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for disassembly.
Carburetor assembly
(1) Screw with washer 3
(2) Carburetor top cover 1
(3) Gasket (carburetor top cover) 1
(4) Plug 1
(5) Screw with washer (float chamber) 2
(6) Float chamber 1
(7) O-ring 1
(8) Float pin 1

EXPLODED DIAGRAM

Step Procedure/Part name Q'ty Service points
(9) Float 1
(10) Needle valve 1
(11) Plug 1
(12) Main nozzle 1
(13) Main jet 1
(14) Pilot jet 1
(15) Pilot screw 1 Except for USA
Reverse the disassembly steps for assembly.

SERVICE POINTS

Carburetor removal

  1. Remove:
    • Float pin (1)
    • Float (2)
    • Needle valve

When removing the float pin (1), tap it in arrow direction (4) from pivot of the pipe joint side (3) as shown.

Carburetor inspection

Do not use a steel wire to clean the jets. This may enlarge the jet diameters and seriously affect performance.

  1. Inspect:
    • Carburetor body
      Cracks/damage ➝ Replace.
      Contamination ➝ Clean.
  2. Inspect:
    • Main jet
    • Pilot jet
    • Main nozzle
      Contamination ➝ Clean.

  1. Inspect:
    • Needle valve
    • Pilot screw (Except for USA)
        Grooved wear ➝ Replace.
  2. Inspect:
    • Float
        Cracks/damage ➝ Replace.

  1. Inspect:
    • O-ring
        Wear/cracks/damage ➝ Replace.

Carburetor installation

  1. Install:
    • Needle valve (3)
    • Float (1)
    • Float pin (2)

• When setting the float (1) into the carburetor, hock the needle valve (3) into the float and insert the needle valve seat.
• When installing the float pin (2), tap the float pin in arrow direction (4) to the pivot of the pipe joint side (5) as shown.
• After installation, make sure that the float operates smoothly.

  1. Measure:
    • Float height (a)
      Out of specification ➝ Replace

Float height : 18.0 ~ 19.0 mm (0.71 ~ 0.75 in)

• Make sure to tilt the carburetor ass'y clockwise 45° for needle valve with spring no load, when measuring the float height.
• Take measurement at the side end of the float, as shown.

Share on social:

Productos relacionados