¡PREPÁRATE PARA EL INVIERNO: Descuentos del 10 al 50 % en todas las piezas OEM!

A menos que lo prohíba el fabricante. No incluye productos de recambio ni productos de la marca Crowley Marine. Precio indicado.

Nuestros almacenes están cerrados el jueves 26 y el viernes 27 de noviembre. ¡Feliz Día de Thanksgiving de los Estados Unidos!

Busca en más de 1 millón de partes originales
Fácil de usar  diagramas de piezas Mejor precio  garantizado Soporte experto  en vivo 50+ años  al servicio de los navegantes Gran selección de piezas OEM  -  de 1950 a 2026 La mayoría de las piezas en stock  -  Cumplimiento el mismo día
Piezas están disponibles- Ejecuta el mismo día

Fuel System [Carburetor] [1996]

Productos relacionados:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1996 150hp All
Yamaha Outboard 1996 175hp All
Yamaha Outboard 1996 200hp All
Yamaha Outboard 1996 225hp All
Yamaha Outboard 1996 250hp All

Fuel System [Carburetor] [1996]
LIT-18616-01-41
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q’ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for removal
Carburetor assembly Refer to "CARBURETOR REMOVAL" section.
1 Drain screw 2
2 Gasket 2
3 Main jet 2
4 Pilot jet plug 2
5 Gasket 2
6 Pilot jet 2
7 Screw 4
8 Float chamber 1
9 Float chamber gasket 1
10 Arm pin 2
11 Float assembly 2
12 Clip 2
13 Needle valve 2
14 Screw 1
15 Air vent cover 1
16 Plug screw 2
17 Gasket 2
18 Pilot screw 2
19 Spring 2
20 Plug screw 1
21 Gasket 1
22 Pilot air jet 2
23 Throttle adjust screw 1 middle carburetor
24 Spring 1
25 Carburetor body 1
Reverse the removal steps for installation.

SERVICE POINTS

Do not use steel wire for cleaning the jets as this may enlarge the jet diameters and seriously affect performance

Carburetor inspection

  1. Inspect:
  • Carburetor body
    Crack/Damage -> Replace.
    Contamination -> Clean.
  1. Inspect:
  • Pilot screw
    Bend/Wear -> Replace.
  1. Inspect:
  • Main jet
  • Pilot jet
  • Main air jet
  • Pilot air jet
  • Main nozzle
    Contamination ->Replace.
  1. Inspect:
  • Needle valve
    Grooved wear -> Replace.
  1. Inspect:
  • Float
    Crack/Damage -> Replace.

Carburetor assembly

  1. Install:
  • Needle valve
  • Float
  • Float pin
  • Screw

NOTE:
After installing, check the smooth movement of the float.

  1. Measure:
  • Float height @
    Out of specification -> Replace.

Float height: 16.0 ± 0.5 mm (0.63 ± 0.02 in)

NOTE:

  • The float should be resting on the needle valve, without compressing it.
  • Measure at the end of the float, opposite to its pivoting end.
  1. Adjust:
  • Pilot screw

Adjustment steps:

  • Screw in the pilot screw until it is lightly seated.
  • Back out by the specified number of turns.

Pilot screw (turns out):
150: 1 ± 1/4
S150: 1-1/4± 1/4
P150:
S: 1-9/16 ± 1/4,
P: 1-1/16 ± 1/4
175: 1-1/16 ± 1/4
S175: 1-1/8± 1/4
P175:
S: 1-5/8 ±1/4,
P: 1-1/8 ± 1/4
200: 1-1/8 ±1/4
S200:
S: 1-1/8 ±1/4,
P: 5/8 ± 1/4
P200, 225:
S: 1-1/4 ± 1/4,
P: 3/4±1/4

Share on social:

Productos relacionados