Step 1: Fuel Component Servicing
Gasoline is extremely flammable and highly explosive under certain conditions. Use caution when working on any part of the fuel system.
Protect against hazardous fuel spray. Before starting any fuel system service, carefully relieve fuel system pressure. Refer to Relieving Fuel System Pressure.
Always disconnect the battery cables at the battery before servicing the fuel system unless instructed to do otherwise.
Always work in a well ventilated area and wipe off any spilled fuel.
DO NOT smoke and make certain no open flames or ignition sources exist.
After servicing the fuel system check for leaks. Failure to check for fuel leakage could allow a leak to go undetected, resulting in fire or explosion.
Step 2: Relieving Fuel System Pressure
IMPORTANT: Minimize fuel system pressure prior to disassembly.
Remove the propeller from the outboard. Then disconnect the electrical connector of the fuel pump and vapor separator assembly.
Start and run the outboard at IDLE for several seconds and STOP the outboard. If the outboard does NOT run, crank for 10 seconds.
Disconnect the battery cables at the battery.
Use the Tests screen of Evinrude Diagnostic software v 6.1 or higher. Select the Vapor Separator button to activate the fuel vapor vent solenoid.

- Vapor Separator button
Step 3: Fuel Filter Service
Disconnect the battery cables at the battery.
Remove fuel filters carefully to prevent spilling the filter’s contents.
Use shop towels to clean up any spilled fuel.
ENVIRONMENTAL NOTE Dispose of fuel contaminated towels in an environmentally responsible manner, or according to local regulations.
Inspect fuel filter contents for any presence of water. If water is present, identify the source and correct the problem. Take additional fuel samples and drain fuel tank(s), if necessary.
Water Separating Fuel Filter
IMPORTANT: Replace the water separating fuel filter when replacing a vapor separator.
Removal
Install hose pinching pliers on the short hose between the fuel filter bracket to the vapor separator assembly. This will prevent fuel from draining out of the vapor separator.

- Hose pinching pliers
Use an appropriate filter wrench to turn the filter in a counterclockwise direction. Remove the filter carefully to prevent spilling the filter’s contents.
Installation
Lubricate filter seal with outboard lubricant and position filter on threaded mounting tube of filter bracket. Take care not to damage water in fuel sensor probe.
Hand tighten until seal contacts filter housing. Then tighten and additional one-half to one turn. Remove the hose pinching pliers from the fuel hose.
Connect the battery cables at the battery.
Run the outboard and check for fuel leaks.
Inline Fuel Filter
Removal
- Inline fuel filter
Installation
Install filter in fuel supply hoses. Note arrow indicating direction of fuel flow on filter. Secure filter with new Oetiker clamps.
Connect the battery cables at the battery.
Run the outboard and check for fuel leaks.
Step 4: Mechanical Fuel Lift Pump Service
The fuel lift pump is serviceable as a complete assembly. Refer to parts catalog for service parts.
Removal
Disconnect the battery cables at the battery.
Disconnect the fuel inlet hose at the rigging center.
Disconnect the fuel outlet hose at the vapor separator.
Disconnect the fuel lift pump pulse hoses at the crankcase fittings.

- Fuel outlet hose at the vapor separator
- Pulse hoses at the crankcase fittings
Remove the fuel lift pump and hoses as an assembly.
Installation
Connect the fuel lift pump pulse hoses to the crankcase. Secure with new Oetiker clamps.
Connect the fuel outlet hose to the vapor separator. Secure with a new Oetiker clamp.
Connect the fuel inlet hose in the rigging center. Secure with a new Oetiker clamp.
Connect battery cables.
Run outboard and check for fuel leaks.
Step 5: Vapor Separator Service
IMPORTANT: Replace the water separating fuel filter when replacing a vapor separator.
Removal
When servicing the fuel system, always shift the outboard to NEUTRAL position, turn the key switch OFF and remove the key, so the outboard cannot be started accidentally.
Relieve fuel system pressure. Refer to Relieving Fuel System Pressure on p. 168.
Disconnect the battery cables at the battery.
Remove the engine top, front and rear covers. Remove the starboard side panel. Remove the starboard frame. Refer to Engine Cover and Frame Service on p. 55.
Use a #2 Posi-drive screwdriver to remove the three screws retaining the center frame to the frame mounts.
Disconnect vapor separator electrical connector.
Carefully remove the Oetiker clamps from the:
- upper & lower water cooling hoses.
- vapor separator vent outlet hose.
- fuel inlet hose at the rigging center.

- Upper & lower water cooling hoses
- Vapor separator vent outlet hose
Place shop towels to catch any spilled fuel. Then remove the following hoses:
- upper & lower water cooling hoses.
- vapor separator vent outlet hose.
- fuel inlet hose from the boat fuel supply hose.
- pulse hoses from the fuel lift pump (AGA & newer models)
Disconnect the fuel rails from the vapor separator. Refer to Quick Connector Locking Fittings on p. 172.
Use shop towels to wipe up any spilled fuel.
Remove the vapor separator, fuel filter bracket and remaining hoses as an assembly:
- Remove the two fuel filter bracket mounting screws and washers.
- Remove the two lower vapor separator mounting screws and washers.
- Remove the vapor separator, fuel filter bracket and hoses from the engine.

- Fuel filter bracket mounting screws and washers
- Vapor separator mounting screws and washers
Place the assembly in a large tray or other suitable container to catch the fuel from the vapor separator. A full assembly can hold over 32 oz. (1 L) of fuel.

ENVIRONMENTAL NOTE Dispose of fuel and fuel contaminated towels in an environmentally responsible manner, or according to local regulations.
Take the assembly to a work bench or other suitable work surface.
Carefully remove Oetiker clamps from:
- inlet hose from inline fuel filter
- outlet hose from fuel lift pump
- inlet hose from water separating fuel filter

- Inlet hose from inline fuel filter
- Outlet hose from fuel lift pump
- Inlet hose from water separating fuel filter
Then remove the hoses.
Installation
After servicing the fuel system check for leaks. Failure to check for fuel leakage could allow a leak to go undetected, resulting in fire or explosion.
Install the following hoses with new Oetiker clamps:
- inlet hose from inline fuel filter
- outlet hose from fuel lift pump
- inlet hose from water separating fuel filter

- Inlet hose from inline fuel filter
- Outlet hose from fuel lift pump
- Inlet hose from water separating fuel filter
Install the vapor separator, fuel filter bracket and hoses on the engine:
- Install the two lower vapor separator mounting screws and washers. Tighten the screws to a torque of 84 to 106 in. lbs. (10 to 12 N·m).
- Install the two fuel filter bracket mounting screws and washers. Tighten the screws to a torque of 84 to 106 in. lbs. (10 to 12 N·m).

- Vapor separator mounting screws and washers
- Fuel filter bracket mounting screws and washers
Connect the fuel rails to the vapor separator. Refer to Quick Connector Locking Fittings on p. 172.
Install the following hoses with new Oetiker clamps:
• upper & lower water cooling hoses
• vapor separator vent outlet hose
• fuel inlet hose at the rigging center

- Upper & lower water cooling hoses
- Vapor separator vent outlet hose
Connect the electrical connector to the vapor separator.
Use a #2 Posi-drive screwdriver to install the center frame screws.
IMPORTANT: Turn self-tapping screws counter clockwise to start the threads and clockwise to tighten. Failure to follow this procedure can damage the threads of the center frame mounts.
Connect battery cables at the battery.
Prime the fuel system and check for fuel leaks. Repair all leaks.
Supply water to the engine. Start and run the outboard and check for fuel leaks. Repair all leaks before returning the outboard to service.
Install starboard frame. Install the engine top, front and rear covers. Install the starboard side panel. Refer to Engine Cover and Frame Service on p. 55.
Step 6: Fuel Rail Service
Quick Connector Locking Fittings
The fuel rails are equipped with quick connector locking fittings. Lift the two tabs of the locking device and push to unlock the quick connector fittings.

- Lift tabs
- Push tabs to unlock
Push the locking device to lock the quick connector fittings. Make sure tabs are in the locked position.

- Push locking device
- Tab in locked position
Removal
Relieve fuel system pressure. Refer to Relieving Fuel System Pressure on p. 168.
When servicing the fuel system, always shift the outboard to NEUTRAL position, turn the key switch OFF and remove the key, so the outboard cannot be started accidentally.
Disconnect the battery cables at the battery.
Remove the engine top, front and rear covers. Remove the port and starboard side panels.
Remove the starboard frame. Next remove the port frame, then remove the front frame.
Use a #2 Posi-drive screwdriver to remove the three screws retaining the center frame to the frame mounts.
Remove the center frame. Refer to Engine Cover and Frame Service on p. 55.
Unlock and remove the quick connectors from the fuel pump & vapor separator assembly.
Use shop towels to wipe up any spilled fuel.

- Quick connector fittings
Unlock the quick connectors from the fuel injectors.
Remove the quick connectors from the fuel injectors.
Use shop towels to wipe up any spilled fuel, then remove the connectors from the fuel injectors.
ENVIRONMENTAL NOTE Dispose of fuel contaminated towels in an environmentally responsible manner, or according to local regulations.
Remove the fuel rails from the engine.
Installation
After servicing the fuel system check for leaks. Failure to check for fuel leakage could allow a leak to go undetected, resulting in fire or explosion.
Check condition of the sealing O-rings on fuel rail fittings. Lubricate O-rings with outboard lubricant.
Position the fuel rails on the engine.
Install the fuel rail fittings on to the fuel fittings of the upper fuel injectors.
- The fuel supply rail uses green locking devices. Position the fuel supply rail on the fitting closest to the cylinder head.
- The fuel return rail uses a red locking device. Position the fuel return rail on the fitting farthest from the cylinder head.
Install the fuel rail fittings on to the fuel fittings of the fuel pump & vapor separator assembly.
- The fuel supply rail uses green locking devices. Position the fuel supply rail on the rearward fitting of the vapor separator.
- The fuel return rail uses a red locking device. Position the fuel return rail on the forward fitting of the vapor separator.
Make sure fittings are fully seated. Push the locking device to lock the quick connector fittings. Make sure tabs are in the locked position.

Install the center frame. Use a #2 Posi-drive screwdriver to install the center frame screws.
IMPORTANT: Turn self-tapping screws counter clockwise to start the threads and clockwise to tighten. Failure to follow this procedure can damage the threads of the center frame mounts.
Next, install the front frame.
Connect the battery cables at the battery.
Prime the fuel system and check for fuel leaks. Repair all leaks.
Supply water to the engine. Start and run the outboard and check for fuel leaks. Repair all leaks before returning the outboard to service.
Install the port frame, followed by the starboard frame.
Install the port and starboard side panels, engine front, top and rear covers. Refer to Engine Cover and Frame Service on p. 55.
Step 7: Fuel Injector Service
Mark fuel injectors to show cylinder locations.
Fuel injectors must be installed in the correct cylinder locations. Use Evinrude Diagnostics software to make sure that EMM programming matches injector positioning. The Injector Coefficients screen displays injector serial numbers.

Injector Coefficients Screen
Use caution when handling fuel injectors. Prevent dirt and debris from entering fuel inlet and outlet ports of injectors or fuel rails. Cover the injector nozzle port in cylinder head to prevent contamination of combustion chamber.
Removal
When servicing the fuel system, always shift the outboard to NEUTRAL position, turn the key switch OFF and remove the key, so the outboard cannot be started accidentally.
Relieve fuel system pressure. Refer to Relieving Fuel System Pressure on p. 168.
Disconnect the battery cables at the battery.
Remove the engine top, front and rear covers. Remove the port and starboard side panels.
Use a #2 Posi-drive screwdriver to remove the three screws retaining the center frame to the frame mounts.
Remove the port and/or starboard frames as required.
Remove the ignition coils:
- Disconnect the electrical connectors from each ignition coil.
- Remove the ignition coil bracket retaining screws and washers.
Disconnect the electrical connector from each fuel injector.
Remove fuel rails from the bank of fuel injectors. Refer to Fuel Rail Service on p. 172.
Use shop towels to catch any spilled fuel.
ENVIRONMENTAL NOTE Dispose of fuel contaminated towels in an environmentally responsible manner, or according to local regulations.
Remove the fuel injectors from the cylinder head as follows:
BOTTOM fuel injector: remove the upper screw completely, then loosen the lower screw several turns (do NOT remove the lower screw).
MIDDLE injector: remove BOTH screws.
TOP injector: remove the lower screw completely, then loosen the upper screw several turns (do NOT remove upper screw).
Remove the upper screw from the TOP injector. Support the injector bank in place on the cylinder head.
Continue to support the injector bank in place while removing the lower screw from the BOTTOM injector.

After the lower screw is detached from the cylinder head, remove the bank of fuel injectors from the cylinder head.
Use a suitable container to drain fuel from the injectors.

Take the bank of fuel injectors to a work bench or other suitable work surface.
Remove fuel injector insulators from the cylinder head.
Fuel Injector Bank Disassembly
Separate the injectors from the injector bank.
To separate the injectors:
- Carefully pull each injector to separate it from the fuel tubes.

• Remove the screw retaining the fuel fitting to the top injector. Then remove the fitting from the injector.
• Remove the screw retaining the fuel fitting to the bottom injector. Then remove the plug fitting from the injector.
• Remove the O-rings from the fuel fitting, each fuel tube and the plug fitting.
Crush Ring Replacement
Injector crush rings must be replaced if injector is installed in a different head or cylinder location.
Use Fuel Injector Puller Kit, P/N 356461, to remove injector from mounting cup.
Turn the nut of the fuel injector puller counterclockwise several turns. Place the fuel injector puller on the fuel injector housing.

- Puller nut
- Fuel injector housing
Align the angled edges of both sides of the tool base with the edge of the fuel injector housing as shown.

- Angled edge of the tool base
Thread the puller screw into the fuel injector 1/4-20 threaded hole until it seats.

- 1/4-20 threaded hole
Turn puller nut clockwise until it contacts the puller base.
Use a 1/2 inch (13 mm) wrench to continue turning the puller nut clockwise.
Turn the puller nut until the fuel injector is removed from the fuel injector housing.

- Fuel injector removed from fuel injector housing
Remove fuel injector puller from injector. Remove crush ring and O-rings from injector. Inspect and clean injector filter. Install new crush ring and O-rings.
Lubricate O-rings with STP† Oil Treatment.Install injector into mount housing. Press on injector face until injector seats in mount housing.

- O-rings
- Crush ring
Installation
After servicing the fuel system check for leaks. Failure to check for fuel leakage could allow a leak to go undetected, resulting in fire or explosion.
All injectors must be installed in the correct cylinder by serial number. Improper injector installation can result in powerhead failure.
Installation of a replacement injector requires that coefficient data for the new injector is uploaded to the EMM.
Coefficient data can be downloaded from the Evinrude dealer website. Refer to the instructions provided with the injector kit.
Upload Coefficient Files to EMM
Use the Evinrude Diagnostics software, v 6.1 or higher Settings screen to upload the coefficient file to the EMM.
Select the Injectors tab.
From the View Injector window, select the cylinder for the injector being replaced. Then select the Replace button.

- “View Injector” window
- “Replace” button
Use the drop down menu to navigate to the saved coefficient file location.
The coefficient file name must match the serial number of the injector.
Select the correct file for the injector.
Select the Open button.

- Drop down menu
- Injector coefficient file
- “Open” button
After the upload is complete, the program will return to the Injector tab.
Make sure the serial number displayed on the screen matches the serial number printed on the serial number label of the replacement injector.

- Injector serial number
Install Injector
Confirm injector location when assembling the injector bank. Refer to cylinder location marks made earlier. Improper injector installation can result in powerhead failure.
Assemble the injector bank:
• Install new O-rings on the fuel fitting, each fuel tube and the plug fitting.
• Apply 2-stroke outboard oil to the O-rings.
• Install the fuel fitting in the top injector.
• Install the retaining screw and tighten to a torque of 84 to 106 in. lbs. (10 to 12 N·m).
• Install the plug fitting in the bottom injector.
• Install the retaining screw and tighten to a torque of 84 to 106 in. lbs. (10 to 12 N·m).
• Align the injectors with the fuel tubes and press together until fully seated.

The following items and their mating surfaces must be cleaned before reassembly:
- Injector
- Cylinder head
- Screws
- Threaded areas
All injector components must be clean to ensure correct torque tightening specifications. To prevent fuel leakage, carefully follow these installation instructions.
IMPORTANT: Be careful not to pinch any wiring or hoses during assembly.
Lubricate mounting screw threads and under the head of the screw with a light coat of Triple-Guard grease. Install washers (one per screw) on injector retaining screws.

Install screws and washers through mounting flange of injector and into cylinder head.
Place insulators over injectors and screws.
Place the injector bank into position on the cylinder head.
Support the injector bank in place on the cylinder head.
Install the lower screw into the BOTTOM injector and cylinder head FIRST.

Install the upper screw into the TOP injector and cylinder head SECOND.
Then install remaining screws.
Tighten screws in stages, starting with the lower screw.
- First torque is 60 to 84 in.lbs. (7 to 9 N·m)
- Second torque is 120 in. lbs. (14 N·m)
- Final torque is 24 to 26 ft. lbs. (33 to 35 N·m).

Tighten Screws in Stages
Install fuel rails. Refer to Fuel Rail Service on p. 172.
Connect the electrical connectors to the fuel injectors.
Install the ignition coils:
- Position the ignition coil & bracket assemblies onto each injector.
- Install the ignition coil bracket washers & retaining screws.
- Connect the electrical connectors to the ignition coils.
Use a #2 Posi-drive screwdriver to install the center frame screws.
IMPORTANT: Turn self-tapping screws counter clockwise to start the threads and clockwise to tighten. Failure to follow this procedure can damage the threads of the center frame mounts.
Connect the battery cables at the battery.
Prime the fuel system and check for fuel leaks. Repair all leaks.
Supply water to the engine. Start and run the outboard and check for fuel leaks. Repair all leaks before returning the outboard to service.
Install the port and/or starboard frames.
Install the engine front, top and rear covers. Install the side panels. Refer to Engine Cover and Frame Service on p. 55.
Step 8: Throttle Valve Service
Removal
Disconnect the battery cables at the battery.
Remove the engine top, front and rear covers. Remove the port and starboard side panels.
Remove the port and starboard frames. Then remove the front frame. Refer to Engine Cover and Frame Service on p. 55.
Use a #2 Posi-drive screwdriver to remove the three screws retaining the center frame to the frame mounts.
Remove the 99.5 mm Oetiker clamp retaining the throttle valve to the plenum.

- 99.5 mm Oetiker clamp
Remove the throttle valve from the plenum. Remove the throttle valve harness from its retainer and disconnect the electrical connector.
Installation
Connect the electrical connector to the throttle valve. Then install the throttle valve harness into its retainer.
Install the throttle valve on to the plenum. Secure the throttle valve to the plenum with a new 99.5 mm Oetiker clamp.
Use a #2 Posi-drive screwdriver to install the center frame screws.
IMPORTANT: Turn self-tapping screws counter clockwise to start the threads and clockwise to tighten. Failure to follow this procedure can damage the threads of the center frame mounts.
Install the front frame. Then install the port and starboard frames.
Install the engine front, top cover and rear covers. Install the port and starboard side panels. Refer to Engine Cover and Frame Service on p. 55.
Connect the battery cables at the battery.
Step 9: Intake Manifold Service
Removal
Disconnect the battery cables at the battery.
Remove the engine top, front and rear covers. Remove the port and starboard side panels.
Remove the port and starboard frames.
Disconnect all cables and hoses at the engine.
Then remove the front frame. Refer to Engine Cover and Frame Service on p. 55.
Remove the four retaining screws from the rigging housing and remove the rigging housing.
Use a #2 Posi-drive screwdriver to remove the three screws retaining the center frame to the frame mounts.
Remove the throttle valve from the plenum, see Throttle Valve Service on p. 180.
Remove the:
- center frame spacers and mounts from the plenum.
- Oetiker clamp from the vapor solenoid vent hose, then remove the vent hose from the plenum.
- electrical connector from the air temperature sensor.

- Oetiker clamp and vent hose
- Electrical connector
- Center frame spacers and mounts
Remove 18 retaining screws from the plenum, then remove the plenum and gasket.

- 18 retaining screws
Remove the tie straps and oil recirculation hoses from the reed plate assembly.

- Tie straps and oil recirculation hoses (oil fill hose removed for clarity)
Remove 5 retaining screws from the reed plate assembly, then remove the reed plate and gasket from the crankcase.

- 5 screws
Disassembly
All reed plate assembly and reed valve assemblies must be cleaned before reassembly. DO NOT use strong carburetor cleaner or the hot soaking tank method for cleaning.
Remove the reed valve retainer screws and remove the assembly.

- Reed valve retainer screws
Use caution to prevent damaging reed valve assemblies.
DO NOT disassemble reed valve assemblies. Damaged reed plates are not serviceable and are replaced as an assembly.
Inspection
Inspect the leaf plate assemblies for damage or contamination:
- Leaf plates must not be distorted.
- Leaf valve must not be cracked or chipped.
- Leaf plate stops must not be distorted or loose.
- Leaf plate assemblies must be clean.
Inspect the intake manifold. All gasket surfaces must be cleaned, smooth, and free of nicks. Use a machinist’s straight-edge and a feeler gauge to check flatness in all directions. Surface must be flat, ±0.004 in. (0.10 mm).

- Straight-edge
Assembly
Remove old adhesive from reed valve retaining screws.
Prime screw threads with Locquic Primer and let dry. Apply Nut Lock to threads. Position reed valve on reed plate and install screws. Tighten screws to a torque of 30 to 42 in. lbs. (3.5 to 4.7 N·m).

- Reed valve retainer screws
Installation
Install gasket on reed plate assembly. DO NOT use sealer on the gasket.
Place reed plate assembly on cylinder/crankcase.
Install all screws.
Tighten the center screws first and expand outward. Tighten in stages to a final torque of 84 to 106 in. lbs. (10 to 12 N·m).

- 5 screws
Install the oil recirculation hoses on to the reed plate assembly. Secure with new tie straps, P/N 317893.

- Tie straps and oil recirculation hoses (oil fill hose removed for clarity)
Place a new gasket on the plenum. Install the plenum on the reed plate and install 18 screws.
Tighten the center screws first and expand outward. Final torque is 84 to 106 in. lbs. (10 to 12 N·m).

- 18 retaining screws
Install the center frame spacers and mounts on the plenum.
Tighten spacers to a torque of 35 to 60 in. lbs. (4 to 6 N·m).
Connect the electrical connector to the air temperature sensor.
Install the vent hose on the plenum and secure with a new 15.7 mm Oetiker clamp.
Install the throttle valve on the plenum, see Throttle Valve Service on p. 180

- Oetiker clamp and vent hose
- Electrical connector
- Center frame spacers and mounts
Use a #2 Posi-drive screwdriver to install the center frame screws.
IMPORTANT: Turn self-tapping screws counter clockwise to start the threads and clockwise to tighten. Failure to follow this procedure can damage the threads of the center frame mounts.
Install the front frame
Install the rigging housing with four retaining screws.
Install the port and starboard frames.
Connect all cables and hoses at the engine. Refer to the Evinrude E-TEC G2 Installation and Predelivery Guide.
Install the engine front, top cover and rear covers. Install the port and starboard side panels.
Refer to Engine Cover and Frame Service on p. 55.
Connect the battery cables at the battery.
