Service Specifications
| HP | 150 | 150 H.O. | 175 | 200 |
|---|---|---|---|---|
| Engine | ||||
| Full Throttle Operating Range | 5000-6000 RPM | 5000-6000 RPM | TBD RPM | TBD RPM |
| Power | 150 HP (110.3kw)@ 5500 RPM | 150 HP (110.3kw) @ 5500 RPM | 175 HP (128.7kw) @ TBD RPM | 200 HP (147.1) @ TBD RPM |
| Idle RPM in NEUTRAL | 500 ± 50 RPM | |||
| Idle RPM in Gear | 500 ± 50 RPM | |||
| Weight (may vary depending on model) | TRAC+ 20 in. (L) Models 487 lbs. (221 kg)TRAC+ 25 in. (X) Models TBD lbs. (TBD kg)Full Featured 20 in. (L) Models TBD lbs. (TBD kg)Full Featured 25 in. (X) Models 532 lbs. (241 kg) | |||
| Engine Type | 66° V 6-Cylinder Loop-Charged | |||
| Displacement | 167 cu. in. (2.7 L, 2743 cm3) | |||
| Bore | 3.386 in. (86 mm) | |||
| Stroke | 3.100 in. (78.74 mm) | |||
| Standard Bore | 3.3853 to 3.3868 in. (85.987 to 86.025 mm) To bore oversize, add piston oversize dimension to standard bore | |||
| Top Crankshaft Journal | 1.6199 to 1.6204 in. (41.15 to 41.16 mm) | |||
| Center Crankshaft Journals | 2.1870 to 2.1875 in. (55.55 to 55.56 mm) | |||
| Bottom Crankshaft Journal | 1.5747 to 1.5752 in. (40.0 to 40.01 mm) | |||
| Rod Crankpin | 1.4995 to 1.5000 in. (38.09 to 38.106 mm) | |||
| Piston Ring End Gap, Both | 0.020 to 0.026 in. (0.55 to 0.66 mm) | |||
| Cooling System | ||||
| Thermostat | 143°F (62°C) | |||
| Maximum Temperature | 203°F (95°C) | |||
| Water pressure – Idle– @ 5000 to 6000 RPM | 5 to 8 psi (34 to 55 kPa)24 to 40 psi (165 to 276 kPa) | |||
| Pressure Relief Valve (open) | 28 to 30 psi (193 to 206 kPa) (approximate) |
| HP | 150 | 150 H.O. | 175 | 200 |
|---|---|---|---|---|
| Fuel / Oil System | ||||
| Fuel/Oil Ratio | EMM Controlled | |||
| Starting Enrichment | EMM Controlled | |||
| Preferred Fuel | Regular unleaded gasoline | |||
| Acceptable Fuel | Use unleaded regular gasoline. The use of unleaded gasoline containing alcohol above the percentage specified by government regulations is not recommended. Do NOT use Fuel labeled "E85." Use of fuel labeled E15 is prohibited by U.S. EPA Regulations. | |||
| Minimum Octane | 87 AKI (R+M)/2 or 90 RON | |||
| Fuel Pressure (minimum) – Lift Pump–High Pressure Pump | 6 psi (41 kPa) @ idle26 to 32 psi (179 to 220 kPa) @ 5500 | |||
| Fuel Pressure (maximum) – Lift Pump–High Pressure Pump | 3 psi (21 kPa) @ 5500 RPM34 to 40 psi (234 to 275 kPa) @ idle RPM | |||
| Maximum Fuel Inlet Vacuum | 4 in. Hg. (13.5 kPa) | |||
| Fuel Filters – Inline– Water Separating | P/N 357797P/N 502906 | |||
| Fuel Additives | 2+4 Fuel Conditioner, Fuel System Cleaner. Use of other additives may result in engine damage. | |||
| Evinrude XD100, Evinrude XD50Synthetic TC-W3 NMMA-certified oil | ||||
| Lubricant – Preferred Lubricant–Acceptable LubricantCapacity – On-Engine Tank Only– With Remote Oil Tank | 2.8 gallons (10.6 liters)2.0 gallons (7.5 liters) | |||
| Electrical System | ||||
| Minimum Battery Requirements | 675 CCA (845 MCA); or 750 CCA (940 MCA) below 32°F (0°C) (Use a 107 amp-hr battery for extreme applications.) | |||
| Alternator | Dual Voltage 50 Amp with Voltage Regulator and Battery Isolation. Refer to Predelivery and Installation Guide for multiple battery applications. | |||
| Analog Tachometer Setting | 6 pulse (12 pole) | |||
| Charging Isolator | Integral, Terminal on Engine Harness | |||
| Engine Fuses | ||||
| Engine Relays – Starter– B+ to 55 V System | 12V 35A SPDT, P/N 301179012V 35A SPDT, P/N 3011790 |
| HP | 150 | 150 H.O. | 175 | 200 |
|---|---|---|---|---|
| Ignition System | ||||
| Type | Inductive Discharge | |||
| Firing Order | 1-2-3-4-5-6 | |||
| Ignition Features | EMM Controlled | |||
| RPM Limit (in gear) | 6250 RPM | |||
| Crankshaft Position Sensor Air Gap | Fixed | |||
| Spark Plug | Champion† To be determined @ 0.028 ± 0.003 in. (0.71 mm) | |||
| Gearcase | ||||
| Gear Ratio | “SLX” Type Gearcase: 12:26 (0.46) (2.16:1) | |||
| Lubricant | HPF Pro Gearcase Lubricant | |||
| Capacity – Standard Rotation – Counter Rotation | Gearcase only – 38.9 fl. oz. (1180 ml)Gearcase, vent hose and oil reservoir 45.6 fl. oz. (1350 ml)Gearcase only – 39 fl. oz. (1154 ml)Gearcase, vent hose and oil reservoir 44.7 fl. oz. (1324 ml) | |||
| Shift Rod Height | Refer to Shift Rod Adjustment on p.420 | |||
| Trim & Tilt System (Full Featured) | ||||
| Lubrication | Power Trim/Tilt Fluid, P/N767969 | |||
| Fluid Capacity | 24 fl. oz. (710 ml) | |||
| Trim Range | 0° to 21° (-6° to 15°) | |||
| Tilt Range | 22° to 81° (16° to 75°) | |||
| Trim & Tilt System (TRAC +) | ||||
| Lubrication | Power Trim/Tilt Fluid, P/N767969 | |||
| Fluid Capacity | 21 fl. oz. (621 ml) | |||
| Trim Range | 0° to 21° (-6° to 15°) | |||
| Tilt Range | 22° to 75° (16° to 69°) | |||
| Steering System (Full Featured) | ||||
| Hydraulic Steering Fluid | SeaStar Hydraulic fluid, P/N 770891 or Hydraulic fluid meeting MIL SPEC: Mil-H-5606 | |||
| Fluid Capacity (NOT including helm or hydraulic hoses) | 10 oz. (300 ml) (approximate) | |||
| Steering Range (lock to lock) | –32° to +32°, 64° Total (see engine Profile Drawing) | |||
| Steering System (TRAC +) | ||||
| Hydraulic Steering Fluid | Refer to steering system manufacturer recommendation | |||
| Steering Range (lock to lock) | –33° to +33°, 66° Total (see engine Profile Drawing) |
