PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual DF70, DF60 Inspection [68][Df70, Df60]

Related Products:
Service Manual DF70, DF60 Inspection [68][Df70, Df60]
99500-99E13-01E
Suzuki Marine

INSPECTION

If excessive ware, cracks, defective or other damage is found on any component, replace component.

Thoroughly wash all metal components with cleaning solvent and dry with compressed air.

Wear safety grasses when using compressed air.

PROPELLER

  • Inspect the propeller for bent, chipped or broken blades. Replace or repair if necessary.

  • Inspect the propeller bushing splines for wear or other dam age. Replace if necessary.

  • Inspect the propeller bushing for deterioration or slipping. Replace if necessary.

GEARCASE

  • Inspect the gearcase for cracks or other damage. Replace if necessary.

  • Inspect the pinion bearing for pitting, rough or other damage. Replace if necessary.

If removal and replacement are required, see the “PINION BEARING” section on the page 9-7.

GEARS

  • Inspect the forward, reverse and pinion gear teeth and the engaging dogs for excessive wear or other damage. Replace if necessary.

  • Inspect the forward gear bearing for pitting, rough or other damage. Replace if necessary.

PROPELLER SHAFT COMPONENTS

  • Inspect the push rod and the push rod pin for excessive wear or other damage. Replace if necessary.

  • Inspect the clutch dog shifter for excessive wear, chip or other damage. Replace if necessary.

  • Inspect the dog pin for bent or other damage. Replace if necessary.

  • Inspect the propeller shaft/splines for wear, twist or other damage. Replace if necessary.

  • Measure the clutch return spring free length.

09900-20101: Vernier calipers

Clutch return spring free length (L)

Standard: 67 mm (2.6 in)

Service limit: 64 mm (2.5 in)

If the measurement exceeds the service limit, replace the clutch return spring.

PROPELLER SHAFT BEARING HOUSING

  • Inspect the housing for cracks or other damage. Replace if necessary.

  • Inspect the propeller shaft bearings and the reverse gear bearing for pitting, rough or other damage. Replace if necessary.

  • Inspect the oil seals and the O-ring for cuts, nicks or tears.

Replacing propeller shaft oil seal

  1. Remove the retaining ring (1) and the washer (2).

  2. Extract the oil seals (3) using the oil seal remover.

09913-50121: Oil seal remover

Do not re-use the oil seal once removed.
Always use a new oil seal.

  1. Apply the Water Resistant Grease to the inner circumference of the housing.

  2. Using an oil seal installer, drive the two oil seals (one at a time) into the housing.

The lipped portion of the seal should face toward the propeller.

Apply the Water Resistant Grease to the seal lips.

99000-25161: SUZUKI WATER RESISTANT GREASE

  1. Install the washer and the retaining ring.

SHIFT ROD GUIDE HOUSING COMPONENTS

  • Inspect the “stepped” surfaces of the shift cam for excessive wear, chip or other damage. Replace if necessary.

  • Inspect the shift rod guide housing for cracks or other dam age. Replace if necessary.

  • Inspect the shift rod guide for excessive wear, pit, corrosion or stiff. Replace if necessary.

  • Inspect the detent ball for wear, rough or other damage. Replace if necessary.

  • Inspect the O-ring for wear, cuts, nicks or tears.

  • Inspect the impeller vanes for cuts, cracks, tears or excessive wear. Replace if necessary.

  • Inspect the pump case and the under panel for cracks, distortion or corrosion. Replace if necessary.

DRIVESHAFT OIL SEAL HOUSING

  • Inspect the housing for cracks or other damage. Replace if necessary.

  • Inspect the oil seals and the O-ring for wear, cuts, nicks or tears.

Replacing driveshaft oil seal

  1. Extract the oil seals using the oil seal remover.

09913-50121: Oil seal remover

  1. Apply the Water Resistant Grease to the inner circumference of the housing.

99000-25161: SUZUKI WATER RESISTANT GREASE

  1. Using an oil seal installer, drive the two oil seals (one at a time) into the housing.

The lipped portion of the seal should face toward the water pump case.

Apply the Water Resistant Grease to the seal lips.

99000-25161: SUZUKI WATER RESISTANT GREASE

DRIVESHAFT

  • Inspect the driveshaft/splines for wear, twist or other damage. Replace if necessary.

  • Inspect the driveshaft bearing for pitting, rough or other dam age. Replace if necessary.

Share on social:

Related Products