PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual DF40, DF50 Engine Control System Structure [230][Df40, Df50]

Related Products:
Service Manual DF40, DF50 Engine Control System Structure [230][Df40, Df50]
99500-87J08-01E
Suzuki Marine

ENGINE CONTROL SYSTEM

Main modifications from “K1” (‘01) model are as follows:

  • For more accurate control, ECM, CKP sensor, flywheel magneto etc. have been modified.

  • Ignition timing and fuel injection timing controls have been modified.

  • The total operating hours indication system has been modified.

  • An oil change reminder system has been added.

  • Self-diagnostic for fuel injector circuit has been added.

ENGINE CONTROL SYSTEM STRUCTURE

SYSTEM STRUCTURE

WIRING DIAGRAM FOR ENGINE CONTROL

ECM CIRCUIT

TERMINAL WIRE COLOR CIRCUIT
1 – –
2 Bl/R Emergency stop switch
3 O Buzzer cancel
4 Y/B Tachometer
5 Br Neutral switch, Engine start signal
6 – –
7 V/W Ex-manifold temperature sensor
8 – –
9 Lg/W Cylinder temperature sensor
10 B Ground for ECM
11 B/W Ground for sensor
12 Bl/B OIL lamp
13 P/B Ground for ECM main relay
14 – –
15 R/B CKP sensor
16 O/Y PC communication
17 G/Y TEMP lamp
18 B/R IAC valve solenoid (–)
19 – –
20 B Ground for power souce
21 – –
22 G No.3 Ignition (–)
TERMINAL WIRE COLOR CIRCUIT
23 Bl Oil pressure switch
24 Lg/R CTP switch
25 P REV-LIMIT lamp
26 G/W CHECK ENGINE lamp
27 Bl/W Buzzer
28 – –
29 W MAP sensor
30 Gr ECM power source
31 Lg/B IAT sensor
32 B Ground for ECM
33 O/G CMP sensor
34 B/G O2 feedback
35 R Power source for MAP sensor
36 Y PC communication
37 B/W Fuel pump (–)
38 R/W No.3 Fuel injector (–)
39 B/Y No.2 Fuel injector (–)
40 O/B No.1 Fuel injector (–)
41 – –
42 B Ground for power source
43 Bl No.2 Ignition (–
44 O No.1 Ignition (–)

“WIRE COLOR” shows the wire color of engine wire harness side.

ECM TERMINAL LAYOUT / TEST CORD

Terminal layout on the ECM is the same as the “❉” marked terminal in the illustration of the 44-pin test cord (special tool P/N. 09930-89950) below.

ECM INTERNAL STRUCTURE

For more accurate control and simplification of structure, CKP sensor and related components have been modified.

CKP SENSOR

Number of pickup coil of CKP sensor assy has been modified from 3 pieces to 1 piece.

FLYWHEEL MAGNETO

Number of reluctor bar (trigger vane) on the flywheel magneto has
been modified from 1 piece to 34 pieces.

CMP SENSOR / INTAKE CAMSHAFT

The CMP sensor on the “K1” (‘01) model is the same as the one
on the previous year models, number of trigger vane on the sensing rotor installed to the intake camshaft, however, has been modified from 1 piece to 4 pieces.

Share on social:

Related Products