PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual 5009011_200–300 HP 90°V Models AA Routine Service [Outboard Rigging Connections]

Related Products:
Service Manual 5009011_200–300 HP 90°V Models AA Routine Service [Outboard Rigging Connections]
5009011
BRP Marine

LIFTING THE OUTBOARD

To avoid personal injury, make sure the lifting capacity of the hoist is at least twice the weight of the outboard.
DO NOT allow the lift hook or chain from the hoist to come in contact with any part of the engine during lifting.

Use correct Lifting Fixture to lift outboard:

Model Lifting Fixture
90° V6 P/N396748 with1 3/4 in. screws

Place lifting tool on flywheel and seat the three screws completely.

  1. Lifting fixture
  2. 1 3/4 in. screws

Fasten appropriate chain hook to eye of tool. Carefully hoist outboard with chain and unbolt outboard mounting brackets from frame.

OUTBOARD RIGGING CONNECTIONS

IMPORTANT: For complete outboard rigging and remote control installation information, refer to the Predelivery and Installation Guide included with the service manual set.

Common Practices – All Models

Control Cable Identification

IMPORTANT: Identify control cable function before rigging outboard.

Identify each control cable:

  • Put the control handle into NEUTRAL position. The throttle cable casing guide will retract completely and the shift cable casing guide will go to the midpoint of its travel.

  1. Shift cable casing guide extended to midpoint
  2. Throttle cable casing guide retracted

Extend the control cables and lubricate them with Triple-Guard grease.

Cable Retainer Clip Installation
When installing retainer clips on control arm link age pins, clips should be locked and must not be bent or deformed.

For proper installation, review the following steps:

  • Place washer on pin.
  • Position retainer clip with straight section on the bottom and angled section on the top.
  • Use long nose pliers to insert straight section of clip into linkage pin hole.

  1. Straight section
  2. Angled section
  • Push the clip towards the hole while lifting on the curved end with the pliers.
  • Be sure retainer clip fully engages the pin.
  • Lock the retainer by moving the angled section behind the straight section.


Locked Retainer Clip

  1. Angled section behind straight section

Cable, Hose, and Wire Routing

To prevent accidental starting while servicing, disconnect the battery cables at the battery. Twist and remove all spark plug leads.

Refer to Control Cable Identification on p. 19

Remove two screws and bracket that fasten the grommet to lower motor cover.

  1. Grommet retaining bracket

Route all hoses, control cables, and wiring through a protective sleeve or conduit into the boat and through the grommet.

The fuel hose may be routed through the protective sleeve or through an alternate hole in the lower motor cover grommet.

To route the fuel hose outside the sleeve, trim the material covering the alternate fuel hose slot in the grommet.

  1. Alternate fuel hose location

Refer to the following diagram to ensure proper positioning of rigging components in grommet.

  1. Fuel supply hose
  2. Fuel supply hose--alternate location
  3. Oil supply hose
  4. Oil tank sending unit harness
  5. Battery cables
  6. Main wire harness (MWS)
  7. Shift cable
  8. Throttle cable
  9. Accessory charge wires
  10. I-Command harness
  11. Water pressure hose
  12. Speedometer hose

  1. Alternate fuel hose location

The main wiring harness, battery cables, oil tank sending unit harness, and any ICON or I-Command network cables should be routed along the same path to the starboard side of the powerhead. Secure all cables with clamps.

After installation, make sure there is enough clearance for all cables to avoid binding or chafing through all engine steering and tilting angles.

Control Cable Installation
Refer to Control Cable Identification on p. 19.

Remove control cable trunnion covers and cable attachment hardware.

  1. Trunnion covers

Shift Cable Installation and Adjustment
Place the shift cable on the shift lever pin and install the washer and retainer clip. Refer to Cable Retainer Clip Installation on p. 20.

IMPORTANT: Do not bend or deform clip.

Make sure the remote control, gearcase, shift linkage, and shift cable are in NEUTRAL.

Hold the shift linkage in NEUTRAL.

Push and pull on the shift cable and observe the cable slack. Hold the casing guide in the center of the slack.

Adjust shift cable trunnion to align with center of the trunnion block. Place cable trunnion in trunnion block.

Install trunnion cover and screw. Tighten screw to a torque of 60 to 80 in. lbs. (7 to 9 N·m).

  1. Shift cable retainer clip and washer
  2. Shift cable trunnion

Throttle Cable Installation and Adjustment
With remote control lever in NEUTRAL, pull firmly on throttle cable casing to remove slack.

Place throttle cable on throttle lever pin and install washer and retainer clip. Refer to Cable Retainer Clip Installation on p. 20.

  1. Throttle cable retainer clip and washer

Make sure that idle stop of the throttle lever is against the crankcase.

  1. Throttle lever stop

Adjust the throttle cable trunnion to align with the trunnion block. Place the cable trunnion in the trunnion block.

IMPORTANT: Move control handle to FORWARD and pull back slowly to NEUTRAL. Make sure the engine throttle lever is against the stop. If not, remove slack by adjusting cable trunnion.

Install trunnion cover and screw. Tighten screw to a torque of 60 to 80 in. lbs. (7 to 9 N·m).

  1. Trunnion cover and screw, throttle cable

Battery Cable Connections
Install battery cables on starter solenoid and main ground stud.

  1. Positive (+) battery connection
  2. Ground (–) connection

SystemCheck Harness Connections
Remove harness connector cover

Before installing electrical connectors, check that the seal is in place. Clean off any dirt from connectors. Apply a light coat of Electrical Grease to the seal only. DO NOT fill connectors with Electrical Grease.

  1. Seal

Connect outboard main wire harness to boat wire harness. Secure connectors in bracket. Refer to the diagram inside of the electrical cover.

  1. Harness connections

BE SURE all harnesses and wires are not pinched, cannot contact flywheel, and do not interfere with moving throttle or shift linkages.

Replace harness connector cover.

I-Command Network Connections
If the outboard will be used with I-Command, or other NMEA 2000 compliant CANbus instruments, use the following connections to supply information to the network:

If using an Evinrude ICON control system, the I-Command Engine Interface Cable, Power Supply Kit, and Ignition and Trim Harness are not required. Connect the I-Command network directly to the ICON gateway module. Refer to the ICON Remote Control System Installation Guide.

If using a mechanical control system, connect the I-Command Engine Interface Cable to the EMM CANbus connector.

  1. EMM CANbus connector

Use an I-Command Ignition and Trim Harness to connect the outboard to the key switch and trim/tilt control. Seal unused SystemCheck connector with 6-Pin Connector Seal, P/N 586076.

If connecting to an existing I-Command Classic network, connect the purple wires between the I-Command Ignition and Trim Harness and the I-Command Engine Interface Cable. This connection supplies power to the network when the key switch is on. I-Command Digital networks do not use this connection.

  1. I-Command Ignition connector
  2. Trim/Tilt connector
  3. SystemCheck connector (with seal)
  4. Network power supply connector (Deutsch style networks)

Route the harnesses around the starboard side of the powerhead along the same path as the battery cable.

For an I-Command oil level display, an accessory CANbus oil level sender must be installed in the oil tank. Connect the sender to the I-Command network. Refer to the I-Command Digital Network Guide.

Use Evinrude Diagnostics software to adjust network settings in the EMM. From the Settings screen, select Engine Options.


Engine Options Screen

ICON Network Connections
If the outboard is equipped for an Evinrude ICON control system, connect the outboard to the network as follows.

Refer to the ICON Remote Control System Installation Guide.

Connect the buss cable from the rear network hub to the outboard’s network harness.

  1. ICON network connector

IMPORTANT: Do not force connectors or locking rings. Properly aligned connectors assemble easily.

Do not use Electrical Grease on ICON buss cable connectors.

To assemble the connectors:
• Use the large tabs and small tabs to carefully align buss cable connectors.
• Carefully align pins and sockets of connectors. Do NOT force connectors together.
• Tighten locking rings of buss connectors finger tight. Do NOT use locking rings to force connectors together.

  1. Large tabs
  2. Small tabs

Do not rotate connectors until they align. This could result in a mismatched connection. It is possible for each pin to enter a socket even if the tabs are misaligned. Look at the tabs to ensure connector alignment prior to making the connection.

Engine Monitor information is distributed to an ICON or I-Command network through the ICON gateway module. Refer to the I-Command Digital Network Guide.

The ICON Harness and Relay Kit, P/N 765296, must be used to provide power to boat accessories that require switched B+. This kit is used in place of connecting accessories to the “A” terminal of the key switch. Accessories connected to the accessory power relay should not exceed 7 amps.

Do not connect boat accessories to the key switch of an ICON system. Connecting accessories to the key switch can cause low current, resulting in erratic operation of the remote control system.

For more information, refer to the ICON Remote Control System Installation Guide.

Water Pressure Gauge
To display engine water pressure, install a water pressure hose fitting in the cylinder block as shown.

Use Pipe Sealant with Teflon on the threads of the hose fitting. Refer to installation instructions supplied with gauge.

Route the water pressure hose around the starboard side of the powerhead along the same path as the battery cables.

  1. Water pressure hose fitting

For an I-Command water pressure display, several water pressure sensor kits are available. Refer to the Evinrude/Johnson Genuine Parts and Accessories catalog.

To send water pressure data to the EMM, along with an I-Command display, install a water pressure transducer kit.

Water pressure readings in excess of 40 psi (275 kpa) are possible for 90° V6 models at boat speeds in excess of 50 mph (80 kph/43 kts).

Use 50 psi Water Pressure Transducer Kit, P/N 5008640.

  1. Water pressure transducer

Connect the transducer lead to the engine wiring harness connector.

  1. Water pressure transducer lead
  2. Engine harness connector
Share on social:

Related Products