POWERHEAD
Remove five inner exhaust housing screws and inner exhaust housing.
007743
- Screws
Remove three exhaust megaphone screws and exhaust megaphone.
007744
- Screws
POWERHEAD DISASSEMBLY
Systems Removal
To simplify reassembly and wiring installation, lay out the various screws and clamps in the order of their proper location.
Remove the oil tank. Refer to Oil Tank Assembly on p. 157.
Remove fuel pump assemblies, filter and fuel injectors. Refer to FUEL COMPONENT SERVICING on p. 130.
IMPORTANT: Mark injectors for cylinder location before removal. All injectors must be installed in their original location. Improper injector installation can result in powerhead failure.
Remove ignition coils.
Remove the electric starter. Refer to Starter Removal on p. 107.
Remove EMM and electrical harness assembly.
Refer to EMM SERVICING on p. 66.
Remove flywheel and stator. Refer to FLYWHEEL
AND STATOR SERVICING on p. 103.
Remove throttle linkage. Refer to Throttle Linkage Removal on p. 177.
Remove shift linkage. Refer to Shift Linkage Removal on p. 177.
Remove the throttle body and reed plate assemblies. Refer to Intake Manifold Service on p. 139.
Remove thermostat and pressure valve assembly.
Refer to THERMOSTAT AND PRESSURE RELIEF VALVE SERVICING on p. 168.
Remove oil supply and recirculation hoses.
Throttle Linkage Removal
Remove throttle cam and throttle lever.
007785
- Throttle cam
- Throttle lever
Shift Linkage Removal
Remove nut from shift lever. Remove shift lever and shaft assembly.
007745
1.Nut
Remove the ball, guide, and spring of the shift detent assembly from the crankcase.
007786
- Shift detent assembly
Cylinder Head Removal
Loosen in stages and remove cylinder head retaining screws. Remove the cylinder head. Discard cylinder head gasket.
007746
- Cylinder head screws (10 total)
Crankcase Disassembly
Remove screws and exhaust side water covers.
007747
IMPORTANT: Use care to avoid bending or damaging inner exhaust side cover.
007787
007788
Remove crankcase flange screws. Loosen in stages and remove the main bearing screws.
007748
- Flange screws
- Main bearing screws
Separate crankcase and cylinder block. It may be necessary to tap on crankshaft with a rawhide or rubber mallet to loosen.
007749
Crankshaft Assembly Removal
Carefully lift crankshaft straight up and remove from crankcase.
007750
Connecting Rods and Pistons
Use an appropriate ring expander to remove all piston rings from pistons. Discard the rings.
Wear safety glasses to avoid injury.
007751
007752
The wrist pin fit is loose on both sides. Push the wrist pin through to free the piston from the connecting rod. If necessary, use Wrist Pin Pressing Tool, P/N 326356, to remove the wrist pin.
007753
Crankshaft Service
Remove upper seal from crankshaft. Discard the seal. A new upper seal must be installed on assembly.
Remove the upper main bearing.
007754
- Upper oil seal
- Upper main bearing
Remove the lower bearing seal housing.
Remove the housing O-ring. Discard O-ring.
007789
Use a punch to remove the housing seal. Discard seal.
007790
1.Punch
Inspect housing and replace if necessary.
Remove the O-ring from crankshaft sleeve and inspect it. Replace the O-ring if it is not in good condition.
007791
Inspect the crankshaft sleeve and replace if necessary. To remove the sleeve, use Slide Hammer, P/N 432128, and Puller Jaws, P/N 432130.
007792
Remove the lower main bearing only if it needs to be replaced. Use external retaining ring pliers to remove the lower bearing retaining ring.
007756
IMPORTANT: If the lower main bearing is removed from the crankshaft, it must be discarded. DO NOT reuse it.
Use a bearing separator to support the bearing, and press off the crankshaft.
007793
