PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual 5008740_200-300 HP 90 ° V Gearcase [Gearcase Disassembly]

Related Products:
Service Manual 5008740_200-300 HP 90 ° V Gearcase [Gearcase Disassembly]
5008740
BRP Marine

Pre-Disassembly Inspection

Wear safety glasses to avoid personal injury, and set compressed air pressure to less than 25 psi (172 kPa).

IMPORTANT: Clean and inspect all parts during disassembly. Replace any damaged parts, seals, O-rings, and gaskets.

Remove the propeller and mounting hardware.

Drain and inspect oil as described in Gearcase Lubricant on p. 37.

Remove gearcase as described in GEARCASE REMOVAL AND INSTALLATION on p. 289.

Remove water pump as described in WATER PUMP SERVICE on p. 292.

Before disassembling the gearcase, examine the following:

● Gearcase Housing — Check for visible damage to skeg, strut, anti-ventilation plate, bullet, and mating surface. Check seal areas for visible signs of lubricant leakage.

● Propeller Shaft — Check for bent or damaged shaft. Check for twisted splines and damaged threads.

● Shift Rod — Check for misadjusted, bent, or binding rod. A misadjusted shift rod height can cause shift difficulty, loss o f boat an d outboard control, and gearcase damage.

● Hydrostatic Seal Grooves — Must be in good condition to help prevent propeller ventilation.

  1. Hydrostatic seal grooves

● Gearcase Anodes — If anodes have eroded to two-thirds their original size, they must be replaced.

  1. Gearcase anode

● Drive Shaft — Check splines for visible damage, twisting and wear. Severe spline wear indicates the exhaust housing or gearcase has been distorted, possibly by impact damage.

● Water Intake Screens — Check for damage and blockage. If screens cannot be cleaned, they must be replaced. Different screens are available and should not be mixed. Refer to correct model parts manual for listing and description.

Propeller Shaft Bearing Housing

Removal

IMPORTANT: Identify gearcase type before disassembly. For counter rotation gearcases, refer to GEARCASE DISASSEMBLY on p. 319.

The propeller shaft bearing housing on “L 2” a nd “M2” models is PRESSED into gearcase housing.

“L2” TYPE GEARCASES

Remove the two screws, washers, and retainers holding the propeller shaft bearing housing.

  1. Retainer tab screws

“M2” TYPE GEARCASES

Remove the two screws holding the propeller shaft bearing housing.

  1. Retainer screws

Remove the propeller shaft bearing ho using from the gearcase using:

● Propeller Shaft Bearing Housing Puller Kit, P/N 354060.

DO NOT use tools designed to push on the propeller shaft. Pushing force against the propeller shaft could damage the forward gear thrust bearing or thrust washer.

IMPORTANT: The L2 type gearcase uses the adaptor ring included with puller kit.

Install the threaded adaptor from the puller kit on to the propeller shaft until seated.

“M2” Type Gearcase

Assemble puller kit components. Hold adaptor with wrench and turn nut clockwise to pull bearing housing.

Pull propeller shaft and bearing housing far enough to loosen the PRESSED bearing housing from the gearcase housing.

“L2” Type Gearcase

“M2” Type Gearcase

Remove the bearing housing, thrust washer, thrust bearing, and reverse gear from gearcase.

Pinion Gear and Driveshaft

Removal

Adjust the shift rod to move the clutch dog as far forward as possible. This will help ease removal of the pinion nut.

Use Driveshaft Holding Socket, P/N 311875, Pin ion Nut Holder, P/N 334455, and Wrench Retainer, P/N 341438 to loosen and remove the pinion nut from the bottom of the driveshaft. Pad handle of holder to prevent damage to gearcase.

  1. Holding socket

  2. Pinion holder

  3. Retainer

Remove the four driveshaft bearing ho using screws.

  1. Driveshaft bearing housing screws

Remove the driveshaft from the gearcase . The bearing housing, shims, thrust bearing, and thrust washer will come out with the driveshaft.

  1. Bearing housing

  2. Shims

  3. Thrust bearing

  4. Thrust washer

If driveshaft cannot be removed, refer to Locked Driveshaft Removal on p. 299.

Remove the pinion gear from the gearcase.

Locked Driveshaft Removal

The driveshaft to pinion taper is a locking taper. If necessary, use Driveshaft Puller, P/N 390706, and Backing Plate , P/N 325867, to break the lock. Install the too ls as shown by clamping them around the driveshaft. Alternately tighten the two vertical screws against the backing plate inserted between the puller and the gearcase until the driveshaft pops loose from the pinion.

  1. Drive shaft

  2. Puller

  3. Backing plate

If upper driveshaft becomes separated from lower driveshaft, use Lower Driveshaft Puller, P/N 342681, to remove . Install puller into lower driveshaft and turn 90° to position hook under pin in driveshaft. Thread Slide Hammer, P/N 391008, into puller and remove driveshaft.

Driveshaft Service

To separate the upper driveshaft (if needed) from the lower driveshaft, remove the roll pin. Replace the damaged component.

To assemble the driveshaft, install new driveshaft retainer into the groove of the upper driveshaft.

Install the upper driveshaft into the lower drive shaft, aligning the holes in the driveshaft retainer and the lower driveshaft.

Install the roll pin to the specified dimension.

  1. Roll pin

Shift Housing, Gear, and Propeller Shaft Removal

Push down on the shift rod. This will move the detent lever downward to clear the inside of the gearcase when the shaft assembly is pulled out. Unscrew the shift rod from the detent lever. Remove screws, cover, and shift rod from the gearcase.

Discard the cover gasket. Remove and discard the shift rod O-ring from inside of cover.

  1. Cover gasket

Remove propeller shaft assembly from gearcase.

Water Intake Screens

Remove and clean water intake screens. Replace if damaged.

  1. Water intake screen

GEARCASE HOUSING INSPECTION

Thoroughly clean gearcase housing to remove all dirt and debris prior to inspection. Inspect pinion bearing and forward thrust surface of gearcase housing.

Use Gearcase Alignment Gauge Kit, P/N 5006349 to check the condition of gearcase housing prior to reassembly. Refer to instructions provided with kit. Use additional Gauging Head as follows:

● P/N 5007750, for “L2” Type gearcase housings

● P/N 5007749, for “M2” Type gearcase housings

Share on social:

Related Products